Rear Airbag Sensor (For 3 Door)

Rear Airbag Sensor (for 3 Door):

REAR AIRBAG SENSOR (for 3 Door)

REMOVAL

CAUTION: Some of the these service operations affect the SRS airbag system. Refer to Restraint Systems Service Precautions before servicing.

NOTE: Always use "Torx" socket wrench E10 when installing the rear seat.

HINT: The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides unless otherwise specified.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
3. REMOVE DECK BOARD SUB-ASSEMBLY
4. REMOVE DECK FLOOR BOX RH
5. REMOVE DECK FLOOR BOX LH
6. REMOVE NO.1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
7. REMOVE NO.2 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
8. REMOVE REAR SEAT ASSEMBLY RH (for Slide Reclining Hold Down Seat Type)
9. REMOVE REAR SEAT ASSEMBLY LH (for Slide Reclining Hold Down Seat Type)
10. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type)
11. REMOVE REAR SEATBACK ASSEMBLY (for Hold Down Seat Type)
12. REMOVE FRONT DOOR SCUFF PLATE RH

13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
a. Remove the rear opening trim weatherstrip to the extent necessary to remove the quarter trim panel assembly front.

14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

15. REMOVE REAR DECK TRIM COVER

16. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

17. REMOVE DECK SIDE TRIM PANEL ASSEMBLY RH
a. Remove the 3 screws.
b. Disengage the 3 clips and the 3 claws and remove the deck side trim panel.

HINT: When removing the deck side trim panel assembly LH disconnect the room light connector and remove the deck side trim panel.

18. REMOVE REAR AIRBAG SENSOR

CAUTION: Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

a. Slide the outer housing and detach the airbag connector.

b. Remove the bolt disengage the hook and remove the airbag sensor.

INSTALLATION

CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

NOTE: Always use "Torx" socket wrench E10 when installing the rear seat.

HINT: The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides unless otherwise specified.

1. INSTALL REAR AIRBAG SENSOR
a. Confirm that the ignition switch is turned to OFF.
b. Confirm that the negative battery terminal is detached.

CAUTION: Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

c. Insert the hook into the body hole and install the airbag sensor with the bolt.

Torque: 9.0 N.m (90 kgf.cm, 80 in.lbf)

NOTE:
- Do not use a rear airbag sensor that has been dropped.
- Do not subject the rear airbag sensor to any impact or force.

d. Confirm that there is no looseness by shaking the rear airbag sensor.

e. Connect the airbag connector.

2. INSTALL DECK SIDE TRIM PANEL ASSEMBLY RH
a. Engage the 3 clips and the 3 claws and install the deck trim side panel.
b. Tighten the 3 screws.

HINT: When installing the deck side trim panel assembly LH connect the room light connector and install the deck side trim panel.

3. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

4. INSTALL REAR DECK TRIM COVER

5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
a. Install the rear door opening trim weatherstrip.

7. INSTALL FRONT DOOR SCUFF PLATE RH
8. INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)
9. INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)
10. INSTALL NO.2 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
11. INSTALL NO.1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
12. INSTALL REAR SEATBACK ASSEMBLY (for Hold Down Seat Type)
13. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type)
14. INSTALL DECK FLOOR BOX RH
15. INSTALL DECK FLOOR BOX LH
16. INSTALL DECK BOARD SUB-ASSEMBLY
17. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)

19. INSPECT SRS WARNING LIGHT