Side Airbag Sensor (For 3 Door)

Side Airbag Sensor (for 3 Door):

SIDE AIRBAG SENSOR (for 3 Door)

REMOVAL

CAUTION: Some of the these service operations affect the SRS airbag system. Refer to Restraint Systems Service Precautions before servicing.

NOTE: Always use "Torx" socket wrench E10 when removing the rear seat.

HINT: The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides unless otherwise specified.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
3. REMOVE DECK BOARD SUB-ASSEMBLY
4. REMOVE DECK FLOOR BOX RH
5. REMOVE DECK FLOOR BOX LH
6. REMOVE NO.1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
7. REMOVE NO.2 REAR SEAT LEG COVER
8. REMOVE REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)
9. REMOVE REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)
10. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type)
11. REMOVE REAR SEATBACK ASSEMBLY (for Hold Down Seat Type)
12. REMOVE FRONT DOOR SCUFF PLATE RH
13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
15. REMOVE SIDE AIRBAG SENSOR

CAUTION: Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

a. Slide the outer housing and detach the airbag connector.

b. Remove the bolt disengage the hook and remove the side airbag sensor.

INSTALLATION

CAUTION: Some of these service operations affect the SRS airbag system. Refer to Restraint Systems Service Precautions before servicing.

NOTE: Always use "Torx" socket wrench E10 when installing the rear seat.

HINT: The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides unless otherwise specified.

1. INSTALL SIDE AIRBAG SENSOR

a. Confirm that the ignition switch is turned to OFF.
b. Confirm that the negative battery terminal is detached.

CAUTION: Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

c. Insert the hook into the body hole and install the airbag sensor with the bolt.

Torque: 9.0 N.m (90 kgf.cm, 80 in.lbf)

NOTE:
- Do not use a side airbag sensor that has been dropped.
- Do not subject the side airbag sensor to any impact or force.

d. Confirm that there is no looseness by shaking the side airbag sensor.

e. Connect the airbag connector.

2. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
3. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
4. INSTALL FRONT DOOR SCUFF PLATE RH
5. INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)
6. INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)
7. INSTALL NO.2 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
8. INSTALL NO.1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
9. INSTALL REAR SEATBACK ASSEMBLY (for Hold Down Seat Type)
10. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type)
11. INSTALL DECK FLOOR BOX RH
12. INSTALL DECK FLOOR BOX LH
13. INSTALL DECK BOARD SUB-ASSEMBLY
14. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)

16. INSPECT SRS WARNING LIGHT