B1647
SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1642/81: Lost Communication with Side Satellite Sensor Bus RH
DTC B1642/81 - Lost Communication with Side Satellite Sensor Bus RH
DTC B1647/82 - Lost Communication with Side Satellite Sensor Bus LH
DESCRIPTION
The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH, and rear airbag sensor LH or RH.
The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1642/81 or B1647/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH).
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. CHECK FOR DTC
(a) Turn the engine switch off.
(b) Turn the engine switch on (IG), and wait for at least 60 seconds.
(c) Check for DTCs. DTC Check / Clear
Result
HINT: Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.
B -- CHECK CONNECTION OF CONNECTORS
A -- USE SIMULATION METHOD TO CHECK
C -- Continue to next step.
2. CHECK CONNECTION OF CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
3. CHECK CONNECTORS
(a) Disconnect the connectors from the center airbag sensor and side airbag sensor RH.
(b) Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
4. CHECK SIDE AIRBAG SENSOR RH CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(c) Turn the engine switch off.
(d) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(e) Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(g) Disconnect the service wire from connector B.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
OK -- Continue to next step.
5. CHECK CONNECTION OF CONNECTORS
(a) Check that the connector is properly connected to the rear airbag sensor RH.
OK:
The connector is properly connected.
NG -- CONNECT CONNECTOR PROPERLY
OK -- Continue to next step.
6. CHECK CONNECTORS
(a) Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
(b) Check that the connector (on the rear airbag sensor RH side) is not damaged.
OK:
The connector is not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
7. CHECK REAR AIRBAG SENSOR RH CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(c) Turn the engine switch off.
(d) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(e) Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(g) Disconnect the service wire from connector E.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
OK -- Continue to next step.
8. CHECK SIDE AIRBAG SENSOR RH
(a) Connect the connector to the center airbag sensor.
(b) Interchange the side airbag sensor LH with RH and connect the connectors to them.
(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in the memory. DTC Check / Clear
(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 90 seconds.
(h) Check for DTCs. DTC Check / Clear
Result
HINT: Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.
(i) Turn the engine switch off.
(j) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(k) Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.
B -- REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH
A -- USE SIMULATION METHOD TO CHECK
C -- Continue to next step.
9. CHECK REAR AIRBAG SENSOR RH
(a) Temporarily replace the rear airbag sensor RH with a new one.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory. DTC Check / Clear
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 90 seconds.
(g) Check for DTCs. DTC Check / Clear
OK:
DTC B1642 is not output.
HINT: Codes other than DTC B1642 may be output at this time, but they are not related to this check.
(h) Turn the engine switch off.
(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- REPLACE REAR AIRBAG SENSOR RH
10. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
(a) Disconnect the No. 2 floor wire connector from the front door wire RH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- REPLACE FRONT DOOR WIRE RH
11. CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
(a) Disconnect the front door wire RH connector from the No. 2 floor wire.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(h) Disconnect the service wire from connector C.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
12. CHECK CONNECTION OF CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor LH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
13. CHECK CONNECTORS
(a) Disconnect the connectors from the center airbag sensor and rear airbag sensor LH.
(b) Check that the connectors (on the center airbag sensor side and rear airbag sensor LH side) are not damaged.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.
14. CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(c) Turn the engine switch off.
(d) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(e) Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(g) Disconnect the service wire from connector B.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.
15. CHECK CONNECTION OF CONNECTOR
(a) Check that the connector is properly connected to the side airbag sensor LH.
OK:
The connector is properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
16. CHECK CONNECTORS
(a) Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.
(b) Check that the connector (on the side airbag sensor LH side) is not damaged.
OK:
The connector is not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
17. CHECK SIDE AIRBAG SENSOR LH CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(c) Turn the engine switch off.
(d) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(e) Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(g) Disconnect the service wire from connector E.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FLOOR WIRE (REAR SIDE AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
OK -- Continue to next step.
18. CHECK REAR AIRBAG SENSOR LH
(a) Temporarily replace the side airbag sensor LH with a new one.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory. DTC Check / Clear
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 90 seconds.
(g) Check for DTCs. DTC Check / Clear
OK:
DTC B1642 or B1647 is not output.
HINT: Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.
(h) Turn the engine switch off.
(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
NG -- CHECK SIDE AIRBAG SENSOR LH
OK -- REPLACE REAR AIRBAG SENSOR LH
19. CHECK SIDE AIRBAG SENSOR LH
(a) Interchange the side airbag sensor RH with LH and connect the connectors to them.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory. DTC Check / Clear
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 90 seconds.
(g) Check for DTCs. DTC Check / Clear
Result
HINT: Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.
(h) Turn the engine switch off.
(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(j) Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
B -- REPLACE SIDE AIRBAG SENSOR LH
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C -- USE SIMULATION METHOD TO CHECK
20. CHECK FLOOR WIRE (REAR SIDE AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
(a) Disconnect the floor wire connector from the front door wire LH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(h) Disconnect the service wire from connector C.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FLOOR WIRE
OK -- REPLACE FRONT DOOR WIRE LH