DTC 59

SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1840/59: Short in Curtain Shield Squib RH 2nd Step Circuit

DTC B1840/59 - Short in Curtain Shield Squib RH 2nd Step Circuit

DTC B1841/59 - Open in Curtain Shield Squib RH 2nd Step Circuit

DTC B1842/59 - Short to GND in Curtain Shield Squib RH 2nd Step Circuit

DTC B1843/59 - Short to B+ in Curtain Shield Squib RH 2nd Step Circuit

DESCRIPTION

The curtain shield squib RH 2nd step circuit consists of the center airbag sensor and the curtain shield airbag RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the rear curtain shield squib RH 2nd step circuit.






WIRING DIAGRAM





INSPECTION PROCEDURE
HINT: To perform the simulation method, enter the "check mode (signal check) with the Techstream Check Mode Procedure, and then wiggle each connector of the airbag system or drive the vehicle on various type of road. Diagnosis System

PROCEDURE

1. CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH 2ND STEP)





(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Disconnect the connector from the curtain shield squib RH 2nd step.
(d) Connect the white wire side of SST (resistance: 2.1 Ohms) to connector C.
CAUTION: Never connect the tester to the curtain shield airbag RH (curtain shield squib RH 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
(e) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs. DTC Check / Clear
(h) Turn the engine switch off.
(i) Turn the engine switch on (IG), and wait for at least 60 seconds.
(j) Check for DTCs. DTC Check / Clear
OK:
DTC B1840, B1841, B1842 or B1843 is not output.
HINT: Codes other than DTC B1840, B1841, B1842 and B1843 may be output at this time, but they are not related to this check.

NG -- CHECK CONNECTOR
OK -- REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH
2. CHECK CONNECTOR
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Disconnect SST from connector C.
(d) Check that the No. 2 floor wire connector (on the curtain shield squib RH 2nd step side) is not damaged.
OK:
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
3. CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD SQUIB RH 2ND STEP CIRCUIT)





(a) Disconnect the connectors from the center airbag sensor.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:





(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:





(g) Release the activation prevention mechanism built into connector B. Diagnosis System
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:






NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
4. CHECK CENTER AIRBAG SENSOR





(a) Connect the connectors to the curtain shield squib RH 2nd step and the center airbag sensor.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs. DTC Check / Clear
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs. DTC Check / Clear
OK:
DTC B1840, B1841, B1842 or B1843 is not output.
HINT: Codes other than DTC B1840, B1841, B1842 and B1843 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK