Diagnosis System
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM (for BOSCH Made): DIAGNOSIS SYSTEM
1. DIAGNOSIS SYSTEM
(a) Inspect the battery voltage.
Standard voltage:
11 to 14 V
(b) If the voltage is below 11 V, recharge the battery before proceeding.
(c) The vehicle's ECU uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.
HINT
Connect the cable of Techstream to the DLC3, turn the ignition switch on (IG) and attempt to use Techstream. If the screen displays a communication error message, a problem exists on either the vehicle side or the tester side.
(d) If the communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.
If the communication is still impossible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.
NOTICE:
*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.
2. DESCRIPTION
NOTICE:
When releasing the parking brake, set chocks to hold the vehicle for safety.
(a) If the skid control ECU detects a malfunction, the ABS warning, BRAKE warning, SLIP indicator and master caution indicator lights will come on in order to warn the driver.
(b) The DTCs are simultaneously stored in the memory. The DTCs can be read by connecting the SST between terminals TC and CG of the DLC3 and observing the blinking pattern of the ABS warning and SLIP indicator lights, by reading the multi-information display (models with multi-information display), or by connecting Techstream. Vehicle Stability Control System (For BOSCH Made).
(c) This system has a signal check function (TEST MODE) Test Mode Procedure.
The DTC can be read by connecting Techstream and observing the blinking pattern of the ABS warning light.
3. WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
(a) Release the parking brake.
NOTICE:
Before releasing the parking brake, move the shift lever to the P position for safety (Automatic Transaxle model) or set the chocks to hold the vehicle for safety (Manual Transaxle model).
HINT
When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light comes on.
(b) When the ignition switch is turned on (IG), check that the ABS warning, BRAKE warning, TRAC OFF indicator, VSC OFF indicator and SLIP indicator lights come on for approximately 3 seconds.
HINT
If the warning light and indicator light check result is not normal, proceed to troubleshooting for the ABS warning, BRAKE warning, TRAC OFF indicator, VSC OFF indicator and SLIP indicator light circuits.
If the indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
4. SYMPTOM SIMULATION
HINT
The most difficult case in troubleshooting is when no symptoms occur. In such cases, a thorough customer problem analysis must be carried out. Then the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be reproduced. No matter how experienced or skilled a technician may be, if they proceeds to troubleshoot without confirming the problem symptoms, they will likely overlook something important and make a wrong guess at some points in the repair operation. This leads to a standstill in troubleshooting.
(a) Vibration method: When vibration seems to be the major cause.
HINT
Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned on (IG)).
(1) Slightly vibrate the part of the sensor considered to be the problem cause with your fingers and check whether the malfunction occurs.
(2) Slightly shake the connector vertically and horizontally.
HINT
Shaking the relays too strongly may result in open relays.
(3) Slightly shake the wire harness vertically and horizontally. The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.