Registration

U660E AUTOMATIC TRANSAXLE: AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION

NOTICE:
* When the automatic transaxle is replaced, the transaxle compensation code must be input into the TCM (Proceed to step 1). After the automatic transaxle is reinstalled, the QR code label will be positioned where the code cannot be read. Therefore, before reinstalling the automatic transaxle, record the transaxle compensation codes or input them in Techstream.
* When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (Proceed to step 2).
1. INPUT TRANSAXLE COMPENSATION CODE INTO TCM

NOTICE:
Transaxle compensation codes are unique, 60-digit alphanumeric values printed on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.

(a) Record the transaxle compensation code specified on the QR label.





HINT
The transaxle compensation code is imprinted on the QR label.

(b) Shift the shift lever to the N or P position.

(c) Connect Techstream to the DLC3.

(d) Turn the ignition switch on (IG).

(e) Turn the tester on.

NOTICE:
Do not start the engine.

(f) Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

(g) Select "Set Compensation Code".

(h) Register the compensation code.

(1) Press "Input".

(2) Manually input the transaxle compensation code. The code is a 60-digit alphanumeric value printed on the QR label. After inputting the code, press "OK".

(i) Check that the compensation code displayed on the screen is correct by comparing it with the 60-digit alphanumeric value on the QR label.

NOTICE:
If an incorrect transaxle compensation code is input into the TCM, shift shock will occur.

(j) Press "NEXT" to set the compensation code to the TCM.

HINT
* If the registration process fails, the compensation code may be incorrect. Check the compensation code again.
* If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause a registration failure. Check the wire harness and the DLC3 connection. If no problem is found, the TCM may be malfunctioning. Check the TCM and repeat this operation.
(k) Press "EXIT".

2. TRANSFER TRANSAXLE COMPENSATION CODE

NOTICE:
Transaxle compensation codes are 60-digit alphanumeric values imprinted on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.

HINT
The following operation is available for use with TCMs that can transmit the registered transaxle compensation code to Techstream.

(a) Shift the shift lever to the N or P position.

(b) Connect Techstream to the DLC3.

(c) Turn the ignition switch on (IG).

(d) Turn the tester on.

NOTICE:
Do not start the engine.

HINT
The transaxle compensation code is imprinted on the QR label.

(e) Read the transaxle compensation code.

(1) Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

(2) Select "Read Compensation Code".

(3) Press "Save".

(4) Press "Save" or "Overwrite".

HINT
Press "Overwrite".

NOTICE:
Do not use the code specified on the transaxle QR label even if the transmission compensation code cannot be read using Techstream. The code printed on an in-service transaxle may not match its current characteristics. Replace the TCM with a new one and perform a road test to allow the TCM to learn.

(5) Press "EXIT".

(6) Turn the ignition switch off.

(f) Replace the TCM.

(g) Set the transaxle compensation code.

(1) Turn the ignition switch on (IG).

(2) Turn the tester on.

(3) Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

(4) Select "Set Compensation Code".

(5) Press "Open".

(6) Press "Open" again to proceed.

(7) Press "Exit".