Replacement

U151E AUTOMATIC TRANSAXLE: DIFFERENTIAL OIL SEAL: REPLACEMENT

1. REMOVE ENGINE UNDER COVER ASSEMBLY Removal

2. REMOVE NO. 1 ENGINE UNDER COVER Removal

3. REMOVE NO. 2 ENGINE UNDER COVER Removal

4. DRAIN AUTOMATIC TRANSAXLE FLUID Removal

5. REMOVE FRONT WHEEL

6. REMOVE FRONT AXLE HUB NUT LH Removal

7. REMOVE FRONT AXLE HUB NUT RH

HINT
Perform the same procedure for the LH side.

8. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH Removal

9. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

10. SEPARATE FRONT SPEED SENSOR LH Removal

11. SEPARATE FRONT SPEED SENSOR RH

HINT
Perform the same procedure for the LH side.

12. SEPARATE TIE ROD ASSEMBLY LH Removal

13. SEPARATE TIE ROD ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

14. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH Removal

15. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT
Perform the same procedure for the LH side.

16. SEPARATE FRONT AXLE ASSEMBLY LH Removal

17. SEPARATE FRONT AXLE ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

18. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH Removal

19. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD) Removal

20. SECURE FRONT AXLE HUB SUB-ASSEMBLY LH Removal

21. SECURE FRONT AXLE HUB SUB-ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

22. REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

(a) Using SST, pull out the oil seal.





SST : 09308-00010

23. REMOVE TRANSAXLE HOUSING OIL SEAL

(a) Using SST, pull out the oil seal.





SST : 09308-00010

24. INSTALL TRANSAXLE HOUSING OIL SEAL

(a) Coat the lip of a new oil seal with MP grease.





(b) Using SST and a hammer, install a new oil seal.

SST : 09316-60011

09316-00011

Oil seal installation depth:

-0.5 to 0.5 mm (-0.020 to 0.020 in.)

25. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

(a) Coat the lip of a new oil seal with MP grease.





(b) Using SST and a hammer, install a new oil seal.

SST : 09223-15020

SST : 09950-70010

09951-07150

Oil seal installation depth:

-0.5 to 0.2 mm (-0.020 to 0.008 in.)

26. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH Installation

27. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD) Installation

28. INSTALL FRONT AXLE ASSEMBLY LH Installation

29. INSTALL FRONT AXLE ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

30. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH Removal

31. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT
Perform the same procedure for the LH side.

32. INSTALL TIE ROD ASSEMBLY LH Installation

33. INSTALL TIE ROD ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

34. INSTALL FRONT SPEED SENSOR LH Installation

35. INSTALL FRONT SPEED SENSOR RH

HINT
Perform the same procedure for the LH side.

36. INSTALL FRONT STABILIZER LINK ASSEMBLY LH Installation

37. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

38. INSTALL FRONT AXLE HUB NUT LH Installation

39. INSTALL FRONT AXLE HUB NUT RH

HINT
Perform the same procedure for the LH side.

40. INSTALL FRONT WHEEL Installation

41. ADD AUTOMATIC TRANSAXLE FLUID

42. INSPECT AUTOMATIC TRANSAXLE FLUID Procedures

43. INSTALL NO. 2 ENGINE UNDER COVER Installation

44. INSTALL NO. 1 ENGINE UNDER COVER Installation

45. INSTALL ENGINE UNDER COVER ASSEMBLY Installation

46. ADJUST FRONT WHEEL ALIGNMENT Installation

47. CHECK ABS SPEED SENSOR SIGNAL Installation