Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2010 >> Highlander 4WD V6-3.5L (2GR-FE) >> Repair and Diagnosis >> Powertrain Management >> Fuel Delivery and Air Induction >> Fuel Pump >> Service and Repair >> Removal and Replacement >> Removal

Removal





2GR-FE FUEL: FUEL PUMP: REMOVAL

1. DISCHARGE FUEL SYSTEM PRESSURE Removal

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Removal

3. REMOVE REAR CENTER SEAT ASSEMBLY

4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

5. REMOVE SEAT TRACK BRACKET COVER LH Removal

6. REMOVE REAR OUTER TRACK BRACKET COVER LH Removal

7. REMOVE REAR INNER TRACK BRACKET COVER LH Removal

8. REMOVE REAR SEAT LEG SIDE COVER LH Removal

9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function) Removal

10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH Removal

11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

12. REMOVE SEAT TRACK BRACKET COVER RH Removal

13. REMOVE REAR OUTER TRACK BRACKET COVER RH Removal

14. REMOVE REAR INNER TRACK BRACKET COVER RH Removal

15. REMOVE REAR SEAT LEG SIDE COVER RH Removal

16. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function) Removal

17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH Removal

18. REMOVE REAR DOOR SCUFF PLATE LH Removal

19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH Removal

20. REMOVE DECK BOARD ASSEMBLY Removal

21. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY Removal

22. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY Removal

23. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Removal

24. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) Removal

25. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) Removal

26. REMOVE DECK SIDE TRIM BOX LH Removal

27. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) Removal

28. REMOVE JACK CARRIER SUPPORT

29. REMOVE JACK CARRIER CUSHION Removal

30. REMOVE JACK ASSEMBLY Removal

31. REMOVE JACK CARRIER ASSEMBLY Removal

32. REMOVE DECK SIDE TRIM BOX RH Removal

33. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) Removal

34. REMOVE REAR MAT Removal

35. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) Removal

36. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) Removal

37. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) Removal

38. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) Removal

39. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) Removal

40. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) Removal

41. REMOVE REAR FLOOR FINISH PLATE Removal

42. REMOVE DECK SIDE TRIM COVER LH Removal

43. REMOVE DECK SIDE TRIM COVER LH Removal

44. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System) Removal

45. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System) Removal

46. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH Removal

47. REMOVE REAR POWER POINT SOCKET ASSEMBLY Removal

48. REMOVE REAR POWER OUTLET SOCKET COVER Removal

49. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function) Removal

50. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function) Removal

51. REMOVE ROPE HOOK ASSEMBLY (for LH Side) Removal

52. REMOVE NO. 2 DECK SIDE TRIM HOOK Removal

53. REMOVE FRONT DECK SIDE TRIM COVER LH Removal

54. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH Removal

55. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH Removal

56. REMOVE REAR FLOOR SERVICE HOLE COVER

(a) Lift up the front floor carpet.

(1) Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)





(2) Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)





(b) Remove the rear floor service hole cover.





(c) Disconnect the fuel pump connector.

57. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

(a) Remove the tube joint clip, and pull out the fuel pump tube.





NOTICE:
* Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.
* It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
* Disconnect the quick connector by hand. Do not use any tools.
* Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
* If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.
(b) Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.





SST : 09808-14020

09808-01410

09808-01420

09808-01430

HINT
* Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
* Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).
(c) Using SST, loosen the fuel pump gauge retainer.





SST : 09808-14020

09808-01410

09808-01420

09808-01430

NOTICE:
* Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
* Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.
HINT
The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

(d) Remove the fuel pump gauge retainer.

(e) Remove the fuel suction tube with pump and gauge.





NOTICE:
Be careful not to bend the arm of the fuel sender gauge.

(f) Remove the gasket from the fuel tank.
pro multis · About Operation CHARM