Operation Check

NAVIGATION: NAVIGATION SYSTEM (w/ DVD Player): OPERATION CHECK

1. Check system normal condition

(a) If the cause of a symptom is any of the following, the corresponding symptom is normal, it is not a malfunction.

(b) The following symptoms are not a malfunction, but are caused by errors inherent in the GPS, gyro sensor, speed sensor, and navigation ECU.

(1) The current position mark may be displayed on a nearby parallel road.

(2) Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

(3) When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

(4) When the vehicle is carried, such as on a ferry, and the vehicle itself is not running, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by GPS.

(5) When the vehicle is driven on a steep hill, the current vehicle position mark may deviate from the correct position.

(6) When the vehicle makes a continuous turn of 360°, 720°, 1080°, etc., the current vehicle position mark may deviate from the correct position.

(7) When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

(8) When the engine switch is turned to ACC or ON on a turntable while parking, the current vehicle position mark may not point in the correct direction. The same will occur when the vehicle starts to move.

(9) When the vehicle is driven on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

(10) When a tire is changed, the current vehicle position mark may deviate from the correct position.

HINT
* The diameter of the tire may change, causing a speed sensor error.
* Performing the "tire change" in calibration mode will allow the system to correct the current vehicle position faster.
2. CHECK PANEL & STEERING SWITCH

HINT
* The navigation receiver assembly panel switches and steering switch are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Panel&Steering Switch Check Mode

(1) Operate each switch and check that the switch names and condition are correctly displayed.

3. CHECK TOUCH SWITCH

HINT
* The touch switches on the screen are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Touch Switch Check

(1) Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT
* A "+" mark is displayed where the display is touched.
* The "+" mark remains on the display even after the finger is removed.
4. CHECK MIC & VOICE RECOGNITION

HINT
* The microphone and microphone input level are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Microphone&Voice Recognition Check

(1) When speaking into the microphone, check that the microphone input level meter changes according to the input level.

(2) Push the recording switch and perform voice recording.

(3) Check that the recording indicator remains on while recording and that the recording can be played normally.

HINT
* For details of this function, refer to Diagnosis Display Detailed Description Navigation System (w/ DVD Player).
* This function is controlled by the built-in navigation ECU.
5. CHECK COLOR BAR

HINT
* The display color on the screen is checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Color Bar Check Mode

(1) Select a color bar from the "Color Bar Check Mode" screen.

(2) Check the display color.

HINT
* The entire screen turns to the color or stripe selected.
* Touch the display to return to the "Color Bar Check" screen.
6. CHECK GPS & VEHICLE SENSORS

HINT
* GPS information, vehicle signals and sensor signals are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) GPS information

(1) When GPS information is displayed, check the GPS conditions.

HINT
* This screen is updated once per second when input signals to the vehicle are changed.
* For details of this function, refer to Diagnosis Display Detailed Description Navigation System (w/ DVD Player).
(e) Select "Sensors Check" from the "GPS & Vehicle Sensors" screen.

(f) Vehicle Sensors

(1) Check all the signals and sensors when vehicle signal information is displayed.

HINT
* The input signals from the vehicle are updated once per second and if any have changed, the screen is updated.
* This screen displays vehicle signals input to the built-in navigation ECU.
* For details of this function, refer to Diagnosis Display Detailed Description Navigation System (w/ DVD Player).
7. CHECK VEHICLE SIGNAL

HINT
* Vehicle signals received by the navigation receiver assembly are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Vehicle Signal Check Mode

(1) When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

HINT
* Only conditions having inputs are displayed.
* This screen displays vehicle signals input to the navigation receiver assembly.
* For details of this function, refer to Diagnosis Display Detailed Description Navigation System (w/ DVD Player).
8. CHECK HANDSFREE VOLUME SETTING

HINT
* The handsfree volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (w/ DVD Player).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Handsfree Volume Setting

(1) Check the handsfree volume level.

NOTICE:
Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the received voice quality is still acceptable after changing this setting.