B1813

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1810/53-B1813/53: Short in Driver Side Squib 2nd Step Circuit


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

HINT
- Perform the simulation method by selecting "check mode" (signal check) with the Techstream Check Mode Procedure.
- After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads Diagnosis System.

PROCEDURE

1. CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)





(a) Turn the ignition switch OFF.

(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(c) Disconnect the z5 connector from the steering pad.

(d) Connect the white wire side of SST (resistance: 2.1 Ohms) to connector E (black connector).

CAUTION:
Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.

SST : 09843-18061

(e) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(f) Turn the ignition switch ON, and wait for at least 60 seconds.

(g) Clear the DTCs DTC Check / Clear.

(h) Turn the ignition switch OFF.

(i) Turn the ignition switch ON, and wait for at least 60 seconds.

(j) Check for DTCs DTC Check / Clear.

OK:

DTC B1810, B1811, B1812 or B1813 is not output.

HINT
Codes other than DTC B1810, B1811, B1812, B1813 maybe output at this time, but they are not related to this check.

NG -- CHECK CONNECTOR

OK -- REPLACE STEERING PAD Removal

2. CHECK CONNECTOR

(a) Turn the ignition switch OFF.

(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(c) Disconnect SST from connector E.

(d) Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

NG -- REPLACE SPIRAL CABLE Removal
OK -- Continue to next step.

3. CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT





(a) Disconnect the connectors from the center airbag sensor.

(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(c) Turn the ignition switch ON.

(d) Measure the voltage according to the value(s) in the table below.

Standard voltage:





(e) Turn the ignition switch OFF.

(f) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(g) Measure the resistance according to the value(s) in the table below.

Standard resistance:





(h) Release the activation prevention mechanism built into connector B Diagnosis System.

(i) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
OK -- Continue to next step.

4. CHECK CENTER AIRBAG SENSOR





(a) Connect the connectors to the steering pad and the center airbag sensor.

(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(c) Turn the ignition switch ON, and wait for at least 60 seconds.

(d) Clear the DTCs DTC Check / Clear.

(e) Turn the ignition switch OFF.

(f) Turn the ignition switch ON, and wait for at least 60 seconds.

(g) Check for DTCs DTC Check / Clear.

Result





HINT
Codes other than DTC B1810, B1811, B1812, B1813 maybe output at this time, but they are not related to this check.

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

C -- USE SIMULATION METHOD TO CHECK Diagnosis System

5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)





(a) Restore the released activation prevention mechanism of connector B to the original condition.

(b) Disconnect the instrument panel wire connector from the spiral cable.

(c) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(d) Turn the ignition switch ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:





(f) Turn the ignition switch OFF.

(g) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(h) Measure the resistance according to the value(s) in the table below.

Standard resistance:





(i) Release the activation prevention mechanism built into connector B Diagnosis System.

(j) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

OK -- REPLACE SPIRAL CABLE Removal