Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2011 >> Camry L4-2.5L (2AR-FE) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> Manufacturer Code Charts >> DTC 41 >> Transmitter ID1 Error - Tire Pressure Monitoring

Transmitter ID1 Error - Tire Pressure Monitoring





TIRE AND WHEEL: TIRE PRESSURE WARNING SYSTEM: C2141/41-C2145/45: Transmitter ID1 Error
C2145/45 - Transmitter ID5 Error

DESCRIPTION

The tire pressure warning valves and transmitters that are installed in the tire and wheel assemblies measure the air pressure of the tires. The measured values are transmitted to the tire pressure warning antenna and receiver on the body as radio waves and then sent to the tire pressure warning ECU. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure value is less than this threshold, the warning light in the combination meter illuminates.

When the internal circuit of a tire pressure warning valve and transmitter is malfunctioning, one of these DTCs is output.





HINT
* It is necessary to perform this procedure in order to identify the malfunctioning tire pressure warning valve and transmitter because it cannot be identified by only the output DTCs.
* DTC C2145/45 is used only when the vehicle is equipped with a ground spare tire.

INSPECTION PROCEDURE

NOTICE:
* When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using Techstream and write them down before removal.
* It is necessary to perform initialization Registration after registration Initialization of the transmitter IDs into the tire pressure warning ECU after the ECU and/or valve and transmitter have been replaced.

PROCEDURE

1. IDENTIFY TRANSMITTER CORRESPONDING TO DTC

(a) Set the tire pressure to the specified value Component Tests and General Diagnostics.

(b) Turn the ignition switch off.

(c) Connect Techstream to the DLC3.

(d) Turn the ignition switch on (IG) and turn the tester on.

(e) Enter the following menus:

(1) Select: Chassis / Tire Pressure Monitor / Data List

(f) Display the "ID Tire Inflation Pressure" data for each wheel using the tester.

(g) Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds. If "ID Tire Inflation Pressure" data displayed on the tester (ID1 to ID5) does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" data was the cause of the output DTC.

HINT
* Identify the malfunctioning tire pressure warning valve and transmitter by rapidly decreasing the tire pressure of each tire.
* Record which "ID Tire Inflation Pressure" data (ID1 to ID5) corresponds to each tire.

Tire Pressure Monitor





HINT
*: It may take about 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 C2121.

(h) Check the DATA LIST.

Result





NOTICE:
* If "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then forcibly transmit the transmitter ID and recheck it.
* Record the transmitter ID and position of transmitters that are normal.

(i) When the "ID Tire Inflation Pressure" data (ID1 to ID5) has changed, repeat this procedure to identify the tire pressure warning valve and transmitter that corresponds to the DTC.

(j) When all of the "ID Tire Inflation Pressure" data (ID1 to ID5) has changed, identify the malfunctioning tire pressure warning valve and transmitter using recorded ID numbers and output DTC.

(k) Set the tire pressures to the appropriate specified values Component Tests and General Diagnostics.

NEXT -- Continue to next step.

2. REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

(a) Replace the identified tire pressure warning valve and transmitter with a new one Removal.

HINT
* Before installing a new tire pressure warning valve and transmitter, read and write down its transmitter ID.
* The IDs for the tire pressure warning valves and transmitters that are not replaced should be checked using the tester and recorded.

NEXT -- Continue to next step.

3. REGISTRATION OF TRANSMITTER ID

(a) Register the transmitter ID for all wheels Registration.

NEXT -- Continue to next step.

4. PERFORM INITIALIZATION

(a) Perform initialization Initialization.

NEXT -- Continue to next step.

5. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)

(a) Turn the ignition switch off.

(b) Connect Techstream to the DLC3.

(c) Turn the ignition switch on (IG) and turn the tester on.

(d) Enter the following menus:

(1) Select: Chassis / Tire Pressure Monitor / Data List

(e) Check the values by referring to the table below.

Tire Pressure Monitor





HINT
* *: It may take about 2 or 3 minutes until the values are displayed.
* If no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.

Result





B -- END

A -- REPLACE TIRE PRESSURE WARNING ECU Removal
pro multis · About Operation CHARM