Stuck in Acceleration Sensor - Vehicle Stability Control System (for ADVICS Made)

BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM (for ADVICS Made): C1232/32,C0371/71,C1234/34,C1243/43-C1245/45,C1279/79,C1381/97: Stuck in Acceleration Sensor
C1381/97 - Acceleration Sensor Power Supply Voltage Malfunction

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, the DTC U0123/62 (malfunction in CAN communication with the yaw rate sensor) and U0124/95 (malfunction in CAN communication with the acceleration sensor) are output.

These DTCs are also output when calibration has not been completed.

DTCs C0371/71 and C1279/79 can be cleared when the yaw rate and acceleration sensor sends a yaw rate and/or acceleration signal or the Test Mode ends. DTCs C0371/71 and C1279/79 are output only in the Test Mode.





WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor, perform zero point calibration Programming and Relearning.

HINT
When U0123/62, U0124/95 or U0126/63 is output together with C1232/32, C1234/34, C1243/43, C1244/44, C1245/45, or C1381/97, inspect and repair the trouble areas indicated by U0123/62, U0124/95 or U0126/63 first.

PROCEDURE

1. CHECK DTC

(a) Clear the DTC Vehicle Stability Control System (for ADVICS Made).

(b) Turn the ignition switch off.

(c) At a speed of 19 mph (30 km/h) or more, drive the vehicle, turn the steering wheel, and decelerate the vehicle (depress the brake pedal).

(d) Turn the ignition switch on (IG) again and check that no CAN communication system DTC is output.

(e) Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210/36) or for zero point calibration of the acceleration sensor undone (C1336/39) are output.

Result:





C -- REPAIR CIRCUIT INDICATED BY OUTPUT DTC Vehicle Stability Control System (for ADVICS Made)

B -- INSPECT CAN COMMUNICATION SYSTEM
A -- Continue to next step.

2. CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

(a) Turn the ignition switch off.

(b) Check that the yaw rate and acceleration sensor has been installed properly Installation.

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.

NG -- INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY
OK -- Continue to next step.

3. INSPECT YAW RATE AND ACCELERATION SENSOR (IG TERMINAL)

(a) Disconnect the yaw rate and acceleration sensor connector.





(b) Turn the ignition switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard voltage:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)
OK -- Continue to next step.

4. INSPECT YAW RATE AND ACCELERATION SENSOR (GND TERMINAL)

(a) Turn the ignition switch off.





(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NOTICE:
Check the yaw rate and acceleration sensor signal after replacement Test Mode Procedure.

HINT
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step Problem Symptoms Table.

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

OK -- REPLACE YAW RATE AND ACCELERATION SENSOR