B2416

LIGHTING (EXT): LIGHTING SYSTEM: B2416: Height Control Sensor Malfunction
B2416 - Height Control Sensor Malfunction

DESCRIPTION

w/o Advanced Parking Guidance System:

The DTC is stored when the headlight leveling ECU assembly detects malfunctions in the rear height control sensor sub-assembly RH power source or rear height control sensor sub-assembly RH.





w/ Advanced Parking Guidance System:

The DTC is stored when the headlight leveling ECU assembly detects malfunctions in the rear height control sensor sub-assembly RH power source, rear height control sensor sub-assembly RH or parking assist ECU.





WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC

(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(b) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B2416 is not output.

NG -- CHECK VEHICLE CONDITION

OK -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting

2. CHECK VEHICLE CONDITION

(a) Check the vehicle condition.

Result





B -- CHECK FOR DTC (ADVANCED PARKING GUIDANCE SYSTEM)
A -- Continue to next step.

3. READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / HL Auto Leveling / Data List.

(e) Read the display on the Techstream.

HL Auto Leveling





OK:

Normal condition listed above is displayed.

NG -- CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - HEIGHT CONTROL SENSOR)
OK -- Continue to next step.

4. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

(a) Connect 3 dry cell batteries (1.5 V) in series.





(b) Remove the rear height control sensor sub-assembly RH Components.

(c) Connect the positive (+) lead from the batteries to terminal 3 (SHB) and the negative (-) lead from the batteries to terminal 1 (SHG).

(d) Measure the voltage between terminals 2 (SHRR) and 1 (SHG) while slowly moving the link up and down.

Standard Voltage:





Text in Illustration





NG -- REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH Components

OK -- REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Components

5. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - HEIGHT CONTROL SENSOR)

(a) Disconnect the A48 headlight leveling ECU assembly connector.

(b) Disconnect the S3 rear height control sensor sub-assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

6. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

(a) Connect 3 dry cell batteries (1.5 V) in series.





(b) Remove the rear height control sensor sub-assembly RH Components.

(c) Connect the positive (+) lead from the batteries to terminal 3 (SHB) and the negative (-) lead from the batteries to terminal 1 (SHG).

(d) Measure the voltage between terminals 2 (SHRR) and 1 (SHG) while slowly moving the link up and down.

Standard Voltage:





Text in Illustration





NG -- REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH Components

OK -- REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Components

7. CHECK FOR DTC (ADVANCED PARKING GUIDANCE SYSTEM)

(a) Check for DTCs Advanced Parking Guidance System.

OK:

DTC "C1628 Height Control Sensor Circuit Malfunction" is not output.

NG -- GO TO ADVANCED PARKING GUIDANCE SYSTEM Advanced Parking Guidance System
OK -- Continue to next step.

8. READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / HL Auto Leveling / Data List.

(e) Read the display on the Techstream.

HL Auto Leveling





OK:

Normal condition listed above is displayed.

NG -- CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - HEADLIGHT LEVELING ECU ASSEMBLY)
OK -- Continue to next step.

9. REPLACE PARKING ASSIST ECU

(a) Temporarily replace the parking assist ECU with a new or normally functioning one Components.

(b) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B2416 is not output.

NG -- REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Components

OK -- END

10. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - HEADLIGHT LEVELING ECU ASSEMBLY)

(a) Disconnect the A48 headlight leveling ECU assembly connector.

(b) Disconnect the L65 parking assist ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

11. REPLACE PARKING ASSIST ECU

(a) Temporarily replace the parking assist ECU with a new or normally functioning one Components.

(b) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B2416 is not output.

NG -- REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Components

OK -- END