Reassembly

INTERIOR PANELS / TRIM: ROOF HEADLINING: REASSEMBLY

1. INSTALL NO. 2 ROOF HEADLINING PAD

(a) Align the markings on the roof headlining assembly with the No. 2 roof headlining pad and install the pad using hot-melt glue as shown in the illustration.





Text in Illustration





2. INSTALL ROOF HEADLINING PAD

(a) Align the markings on the roof headlining assembly with the roof headlining pad and install the pad using hot-melt glue as shown in the illustration.





Text in Illustration





3. INSTALL NO. 2 ROOF HEADLINING SET PLATE RH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 2 roof headlining set plate RH and install the set plate using hot-melt glue as shown in the illustration.





Text in Illustration





4. INSTALL NO. 2 ROOF HEADLINING SET PLATE LH (w/o Sliding Roof)

HINT
Use the same procedure described for the RH side.

5. INSTALL NO. 1 ROOF WIRE

(a) Apply double-sided tape as shown in the illustration.

(b) Peel off the release paper from the double-sided tape.

(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.





Text in Illustration





Double-sided Tape Size:

X
1 mm (0.0394 in.)

Y
20 mm (0.787 in.)

Z
40 mm (1.57 in.)

(d) Align the pink marking tape (A) on the vehicle front side on the No. 1 roof wire with the vehicle front side tab on the roof headlining, and apply adhesive tape.

HINT
Make sure that the No. 1 roof wire is not twisted and that the marking line (white) faces up.

(e) Turn the visor connector RH clockwise approximately 45° to install the connector to the roof headlining assembly.

(f) Align the pink marking tape (B) on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.

(g) Engage each clamp.

(h) Align the pink marking tape (C) on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.

(i) Turn the visor connector LH clockwise approximately 45° to install the connector to the roof headlining assembly.

(j) Attach the No. 1 roof wire, starting from the front of the vehicle, while aligning it with the double-side tape.

NOTICE:
* Securely attach the No. 1 roof wire.
* If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.

HINT
Secure the extra length of the No. 1 roof wire in the adjustment area.

(k) Apply adhesive tape by aligning it with the markings on the roof headlining.





Text in Illustration





Adhesive Tape Size:

X
20 mm (0.787 in.)

Y
100 mm (3.94 in.)

6. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/o Manual (SOS) Switch) Installation

7. INSTALL TELEPHONE AND GPS ANTENNA CORD SUB-ASSEMBLY (w/ Manual (SOS) Switch) Installation

8. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 3 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.





Text in Illustration





NOTICE:
Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

9. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.





Text in Illustration





10. INSTALL VANITY LIGHT ASSEMBLY

(a) Install the vanity light assembly Installation.

HINT
Use the same procedure for the other vanity light.