Removal
WINDSHIELD / WINDOW GLASS: WINDSHIELD GLASS: REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE WINDSHIELD WIPER ARM COVER Removal
3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH Removal
4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE) Removal
5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH Removal
6. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY Removal
7. REMOVE ANTENNA ORNAMENT Removal
8. REMOVE FRONT FENDER SIDE PANEL UPPER RH Removal
9. REMOVE FRONT FENDER SIDE PANEL UPPER LH Removal
10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY Removal
11. REMOVE COWL TOP VENTILATOR LOUVER RH Removal
12. REMOVE COWL TOP VENTILATOR LOUVER LH Removal
13. REMOVE FRONT DOOR SCUFF PLATE RH Removal
14. REMOVE FRONT DOOR SCUFF PLATE LH Removal
15. REMOVE ACCESS DOOR SCUFF PLATE RH Removal
16. REMOVE ACCESS DOOR SCUFF PLATE LH Removal
17. REMOVE FRONT FLOOR FOOTREST Removal
18. REMOVE FOOTREST CLIP Removal
19. REMOVE COWL SIDE TRIM BOARD RH Removal
20. REMOVE COWL SIDE TRIM BOARD LH Removal
21. REMOVE ROOF SIDE INNER GARNISH COVER RH Removal
22. REMOVE ROOF SIDE INNER GARNISH COVER LH Removal
23. REMOVE ROOF SIDE RAIL GARNISH RH Removal
24. REMOVE ROOF SIDE RAIL GARNISH LH Removal
25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH Removal
26. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH Removal
27. REMOVE ASSIST GRIP PLUG Removal
28. REMOVE ASSIST GRIP ASSEMBLY Removal
29. REMOVE VISOR SUB-ASSEMBLY RH Removal
30. REMOVE VISOR SUB-ASSEMBLY LH Removal
31. REMOVE FRONT PILLAR GARNISH RH Removal
32. REMOVE FRONT PILLAR GARNISH LH Removal
33. REMOVE VISOR ASSEMBLY RH Removal
34. REMOVE VISOR ASSEMBLY LH Removal
35. REMOVE VISOR HOLDER Removal
36. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER Removal
37. REMOVE INNER REAR VIEW MIRROR ASSEMBLY Removal
38. REMOVE ROOM LIGHT ASSEMBLY Removal
39. REMOVE ROOF HEADLINING
HINT
It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.
40. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY
41. REMOVE ROOF DRIP SIDE FINISH MOULDING RETAINER
42. REMOVE FRONT PILLAR OUTER GARNISH
43. REMOVE ROOF SIDE GARNISH PROTECTOR
44. REMOVE WINDSHIELD OUTSIDE LOWER MOULDING
(a) Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
(b) Disengage the 6 claws and remove the windshield outside lower moulding.
45. REMOVE WINDSHIELD OUTSIDE MOULDING
(a) Using a knife, cut off the windshield outside moulding, as shown in the illustration.
NOTICE:
Do not damage the vehicle body with the knife.
(b) Remove the windshield outside moulding.
HINT
Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.
46. REMOVE WINDSHIELD GLASS
(a) Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
(b) From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.
(c) Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
NOTICE:
* When separating the windshield glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
* To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
(d) Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.
HINT
Matchmarks do not need to be placed unless the windshield glass is going to be reused.
(e) Cut through the adhesive by pulling the piano wire around the windshield glass.
(f) Disengage the 2 stoppers.
(g) Using suction cups, remove the windshield glass.
NOTICE:
Leave as much adhesive on the vehicle body as possible when removing the windshield glass.