Part 1

INTERIOR: ROOF HEADLINING: INSTALLATION

HINT
A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.

1. INSTALL REAR ROOF SIDE RAIL PAD LH (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear roof side rail pad LH and install the pad using hot melt glue as shown in the illustration.

2. INSTALL REAR ROOF SIDE RAIL PAD RH (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear roof side rail pad RH and install the pad using hot melt glue as shown in the illustration.

3. INSTALL ROOF SIDE RAIL GARNISH PAD LH (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof side rail garnish pad LH and install the pad using hot melt glue as shown in the illustration.

4. INSTALL ROOF SIDE RAIL GARNISH PAD RH (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof side rail garnish pad RH and install the pad using hot melt glue as shown in the illustration.

5. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY Installation

6. INSTALL NO. 1 ROOF WIRE

(a) Peel off the release paper from the double-sided tape.

(b) Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.

(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

NOTICE:

Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

7. INSTALL NO. 1 AIR OUTLET REGISTER ASSEMBLY

(a) Engage the 10 claws and install the No. 1 air outlet register assembly into the roof side air outlet register.

8. INSTALL NO. 2 ROOF HEADLINING SUPPORT

(a) Align the markings on the roof headlining assembly with the No. 2 roof headlining supports and install the headlining supports using hot melt glue as shown in the illustration.

9. INSTALL NO. 4 ROOF SILENCER PAD

(a) Align the markings on the roof headlining assembly with the No. 4 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

10. INSTALL NO. 2 ROOF HEADLINING PAD

(a) Align the markings on the roof headlining assembly with the 2 No. 2 roof headlining pads and install the pads using hot melt glue as shown in the illustration.

11. INSTALL ROOF HEADLINING PAD

(a) Align the markings on the roof headlining assembly with the 2 roof headlining pads and install the pads using hot melt glue as shown in the illustration.

12. INSTALL NO. 1 ROOF HEADLINING SUPPORT

(a) Align the markings on the roof headlining assembly with the 2 No. 1 roof headlining supports and install the headlining supports using hot melt glue as shown in the illustration.

13. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

14. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 1 roof silencer pad and install the silencer pad using hot melt glue as shown in the illustration.

15. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear No. 2 side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

16. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

17. INSTALL FRONT SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the front side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

18. INSTALL FRONT SIDE RAIL SPACER RH (w/o Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

19. INSTALL VANITY LIGHT ASSEMBLY

(a) Engage the 3 claws and install the vanity light assembly.

20. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.

NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Install the 4 clips.

(c) Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

(d) Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

(e) Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

(f) Connect the No. 1 roof wire connector and engage the 3 clamps to the front pillar LH.

NOTICE:
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

21. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.

NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Install the 3 clips.

(c) Connect the sliding roof drive gear connector.

(d) Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

(e) Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

(f) Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

(g) w/ Rear Seat Entertainment System:

(1) Connect the No. 1 roof wire connector to the rear pillar LH.

(h) Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.

NOTICE:
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

22. INSTALL VISOR HOLDER

(a) Engage the 2 claws.

(b) Push in the visor holder as shown in the illustration.

HINT
Use the same procedure for the RH side and the LH side.

23. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

(a) Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.

NOTICE:
After installation, check that the corners fit correctly.

24. INSTALL ROOF HEADLINING TRIM CLIP STOPPER

(a) Install the roof headlining trim clip stopper with the bolt.

(b) Engage the 3 claws.

HINT
Use the same procedure for the RH side and the LH side.

25. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof)

(a) Assemble the assist grip assembly as shown in the illustration.

(b) Install the assist grip assembly.

HINT
Use the same procedure for the other 4 assist grips.

26. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

(a) Assemble the rear assist grip sub-assembly as shown in the illustration.

(b) Install the rear assist grip sub-assembly.

HINT
Use the same procedure for the RH side and the LH side.

27. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

(a) Assemble the front assist grip sub-assembly as shown in the illustration.

(b) Install the front assist grip sub-assembly.

HINT
Use the same procedure for the RH side and the LH side.

28. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System) Installation

29. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System) Installation

30. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

(a) Engage the 4 claws and install the lens cover.

(b) Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.

31. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

(a) Engage the 4 claws and install the lens cover.

(b) Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.

32. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation

33. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.

34. INSTALL VISOR BRACKET COVER (for LH Side)

(a) Engage the 4 claws and install the visor bracket cover.

35. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

36. INSTALL VISOR BRACKET COVER (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

37. INSTALL ROOF CONSOLE BOX ASSEMBLY

(a) Connect the connector.

(b) Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.

38. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

(a) Engage the 2 guides and 5 clips.

(b) Install the roof side inner garnish assembly LH with the bolt.

(c) Engage the 2 guides and 2 claws, and install the No. 2 seat outer belt guide.

39. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

(a) Engage the 2 guides and 5 clips.

(b) Install the roof side inner garnish assembly LH with the bolt.

(c) Engage the 2 guides and 2 claws, and install the No. 2 seat outer belt guide.

40. INSTALL QUARTER PILLAR GARNISH LH

(a) Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

(b) Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.