Part 3

INTERIOR: ROOF HEADLINING: INSTALLATION - (Continued)

84. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.





85. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

86. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.





87. INSTALL FRONT PILLAR GARNISH LH





(a) Remove the protective cover.





(b) Make sure that the front pillar garnish clip is not damaged.

NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the 3 guides.

(d) Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish LH.

HINT
Tape the tips of the needle-nose pliers before use.





(e) Engage the 2 clips to install the front pillar garnish LH.

88. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

89. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the claw and clip, install the cowl side trim sub-assembly LH.





(b) Install the clip.

90. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the guide and the 8 claws, and install the front door scuff plate LH.





91. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

92. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

93. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

94. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

95. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

96. INSTALL FRONT PILLAR GARNISH RH





(a) Remove the protective cover.





(b) Make sure that the front pillar garnish clip is not damaged.

NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the 3 guides.

(d) Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish RH.

HINT
Tape the tips of the needle-nose pliers before use.





(e) Engage the 2 clips to install the front pillar garnish RH.

97. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

98. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

99. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

100. INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for LH Side) Installation

101. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (for LH Side) Installation

102. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side) Installation

103. INSTALL REAR SEAT LEG SIDE COVER LH (for LH Side) Installation

104. INSTALL RECLINING HINGE COVER LH (for LH Side) Installation

105. INSTALL REAR INNER TRACK BRACKET COVER LH (for LH Side) Installation

106. INSTALL REAR OUTER TRACK BRACKET COVER LH (for LH Side) Installation

107. INSTALL REAR SEAT TRACK BRACKET COVER LH (for LH Side) Installation

108. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side) Installation

109. INSTALL REAR CENTER SEAT ASSEMBLY (for LH Side)

110. INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for RH Side) Installation

111. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

112. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side) Installation

113. INSTALL REAR SEAT LEG SIDE COVER RH (for RH Side) Installation

114. INSTALL REAR INNER TRACK BRACKET COVER RH (for RH Side) Installation

115. INSTALL REAR OUTER TRACK BRACKET COVER RH (for RH Side) Installation

116. INSTALL REAR SEAT TRACK BRACKET COVER RH (for RH Side) Installation

117. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side) Installation

118. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

119. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY





(a) Attach the 2 guides to install the battery service hole cover.

(b) Install the clip.

120. INSTALL DECK BOARD ASSEMBLY





(a) Install the deck board.