C1271
BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1271, C1272, C1275, C1276: Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
C1276 - Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
DESCRIPTION
DTCs C1271 to C1276 will be cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs from C1271 to C1276 are output only in Test Mode.
HINT
* DTCs C1271 and C1275 are for the front speed sensor RH.
* DTCs C1272 and C1276 are for the front speed sensor LH.
WIRING DIAGRAM
Refer to DTCs C1401 and C1402 C1401.
INSPECTION PROCEDURE
NOTICE:
When replacing the brake actuator assembly, perform zero point calibration and store system information Programming and Relearning.
PROCEDURE
1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC Check for Intermittent Problems.
ABS/VSC/TRAC
Result
HINT
Perform the above inspection before removing the sensor and connector.
B -- READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
C -- CHECK FRONT SPEED SENSOR INSTALLATION
A -- Continue to next step.
2. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
(a) Turn the ignition switch off.
(b) Repair or replace the harness or connector.
(c) Check for any momentary interruption between the skid control ECU and the front speed sensor Check for Intermittent Problems.
(d) Check that there are no momentary interruptions.
NEXT -- Continue to next step.
3. PERFORM TEST MODE (SIGNAL CHECK)
(a) Turn the ignition switch off.
(b) Perform the sensor check in the Test Mode procedure Test Mode Procedure.
OK:
All Test Mode DTCs are cleared.
NG -- READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
OK -- END
4. READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Start the engine.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / ABS/VSC/ TRAC / Data List.
(f) Select the Data List on the Techstream Data List / Active Test.
ABS/VSC/TRAC
(g) Check that the speed value output from the speed sensor displayed on the Techstream.
HINT
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart On-Vehicle Inspection.
OK:
The speed value output from the speed sensor displayed on the Techstream is the similar speed as indicated on the speedometer.
NG -- CHECK FRONT SPEED SENSOR INSTALLATION
OK -- Continue to next step.
5. PERFORM TEST MODE (SIGNAL CHECK)
(a) Turn the ignition switch off.
(b) Perform the sensor check in the Test Mode procedure Test Mode Procedure.
OK:
All Test Mode DTCs are cleared.
NG -- CHECK FRONT SPEED SENSOR INSTALLATION
OK -- CHECK FOR INTERMITTENT PROBLEMS How To Proceed With Troubleshooting
6. CHECK FRONT SPEED SENSOR INSTALLATION
(a) Turn the ignition switch off.
(b) Check the speed sensor installation.
OK:
There is no clearance between the sensor and the front steering knuckle.
The installation bolt is tightened properly.
Torque
8.0 N*m (82 kgf*cm, 71 in.*lbf)
Text in Illustration
NG -- INSTALL FRONT SPEED SENSOR CORRECTLY Installation
OK -- Continue to next step.
7. CHECK FRONT SPEED SENSOR TIP
(a) Remove the front speed sensor Removal.
(b) Check the speed sensor tip.
OK:
No scratches, oil, or foreign matter on the sensor tip.
NOTICE:
Check the speed sensor signal after cleaning or replacement Test Mode Procedure.
NG -- CLEAN OR REPLACE FRONT SPEED SENSOR
OK -- Continue to next step.
8. CHECK FRONT SPEED SENSOR ROTOR
(a) Remove the front speed sensor rotor Removal.
(b) Check the speed sensor rotor.
OK:
No scratches, oil, or foreign matter on the rotor.
NOTICE:
Check the speed sensor signal after cleaning or replacement Test Mode Procedure.
HINT
If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
NG -- CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR
OK -- Continue to next step.
9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
(b) Disconnect the skid control ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
for LH
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
10. INSPECT SKID CONTROL ECU (SENSOR INPUT)
(a) Reconnect the skid control ECU connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for RH
for LH
Text in Illustration
NG -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal
OK -- Continue to next step.
11. PERFORM TEST MODE (SIGNAL CHECK)
(a) Turn the ignition switch off.
(b) Perform the sensor check in the Test Mode procedure Test Mode Procedure.
OK:
All Test Mode DTCs are cleared.
NG -- REPLACE FRONT SPEED SENSOR
OK -- CHECK FOR INTERMITTENT PROBLEMS How To Proceed With Troubleshooting
12. REPLACE FRONT SPEED SENSOR
(a) Turn the ignition switch off.
(b) Replace the front speed sensor Removal.
NOTICE:
Check the speed sensor signal after replacement Test Mode Procedure.
NEXT -- Continue to next step.
13. PERFORM TEST MODE (SIGNAL CHECK)
(a) Perform the sensor check in the Test Mode procedure Test Mode Procedure.
OK:
All Test Mode DTCs are cleared.
NG -- REPLACE FRONT SPEED SENSOR ROTOR
OK -- END
14. REPLACE FRONT SPEED SENSOR ROTOR
(a) Turn the ignition switch off.
(b) Remove the front drive shaft assembly Removal.
(c) Replace the front drive outboard joint shaft assembly (front speed sensor rotor) Disassembly.
HINT
If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
NOTICE:
Check the speed sensor signal after replacement Test Mode Procedure.
NEXT -- Continue to next step.
15. PERFORM TEST MODE (SIGNAL CHECK)
(a) Perform the sensor check in the Test Mode procedure Test Mode Procedure.
OK:
All Test Mode DTCs are cleared.
NG -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal
OK -- END