Removal

INTERIOR: ROOF HEADLINING (for Double Cab): REMOVAL

1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Service Precautions.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

3. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

(a) Slide the inner rear view mirror cover in the direction indicated by the arrow in the illustration to disengage the 2 claws from the roof headlining, and then disengage the 2 claws of the inner rear view mirror cover from the mirror and remove the inner rear view mirror cover.

(b) Disconnect the connector.

4. REMOVE SEAT TRACK COVER LH Removal

5. REMOVE SEAT TRACK COVER RH

(a) for Separate Folding Seat Type:

(1) Remove the seat track cover RH Removal.

(b) for Separate Seat Type Front Passenger Side:

(1) Remove the seat track cover RH Removal.

6. REMOVE FRONT SEAT ASSEMBLY LH Removal

7. REMOVE FRONT SEAT ASSEMBLY RH

(a) for Separate Folding Seat Type:

(1) Remove the front seat assembly RH Removal.

(b) for Separate Seat Type Front Passenger Side:

(1) Remove the front seat assembly RH Removal.

8. REMOVE REAR SEAT CUSHION ASSEMBLY LH Removal

9. REMOVE REAR SEAT CUSHION ASSEMBLY RH Removal

10. REMOVE REAR SEAT BACK HINGE COVER

(a) for LH Side:

(1) Remove the rear seat back hinge cover Removal.

(b) for RH Side:

(1) Remove the rear seat back hinge cover Removal.

11. REMOVE REAR SEAT BACK ASSEMBLY LH Removal

12. REMOVE REAR SEAT BACK ASSEMBLY RH Removal

13. REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY LH Removal

14. REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT
Follow the same procedures as for the rear seat back hinge sub-assembly LH.

15. REMOVE FRONT FLOOR FOOTREST Removal

16. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the 9 claws and remove the front door scuff plate.

17. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Follow the same procedures as for the front door scuff plate LH.

18. REMOVE COWL SIDE TRIM BOARD LH

(a) Remove the clip.

(b) Disengage the 2 clips and remove the cowl side trim board.

19. REMOVE COWL SIDE TRIM BOARD RH

HINT
Follow the same procedures as for the cowl side trim board LH.

20. REMOVE REAR DOOR SCUFF PLATE LH

(a) Disengage the 8 claws and remove the rear door scuff plate.

21. REMOVE REAR DOOR SCUFF PLATE RH

HINT
Follow the same procedures as for the rear door scuff plate LH.

22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the front door opening trim weatherstrip.

23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Follow the same procedures as for the front door opening trim weatherstrip LH.

24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the rear door opening trim weatherstrip.

25. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Follow the same procedures as for the rear door opening trim weatherstrip LH.

26. REMOVE FRONT PILLAR GARNISH LH

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

Text in Illustration

HINT
Follow the same procedures as for the opposite side.

(b) Remove the 2 screws.

(1) Using a clip remover, remove the 3 wire harness clamps.

(e) w/ Curtain Shield Airbag:

Text in Illustration

NOTICE:
Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.

(1) Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

27. REMOVE FRONT PILLAR GARNISH RH

HINT
Follow the same procedures as for the front pillar garnish LH.

28. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) Removal

29. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) Removal

30. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY

(a) for Automatic Transmission:

(1) Remove the rear console upper panel sub-assembly Removal.

(b) for Manual Transmission:

(1) Remove the rear console upper panel sub-assembly Removal.

31. REMOVE REAR CONSOLE BOX ASSEMBLY Removal

32. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission) Removal

33. REMOVE FRONT CONSOLE BOX

(a) for Automatic Transmission:

(1) Remove the front console box Removal.

(b) for Manual Transmission:

(1) Remove the front console box Removal.

34. REMOVE AIR CONDITIONING CONTROL ASSEMBLY Removal

35. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) Removal

36. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) Removal

37. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY Disassembly

38. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL Removal

39. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

40. REMOVE COMBINATION METER ASSEMBLY Removal

41. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

42. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

43. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY Removal

44. REMOVE INSTRUMENT LOWER PANEL Removal

45. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY Removal

46. REMOVE INSTRUMENT SIDE PANEL Removal

47. DISCONNECT PASSENGER AIRBAG CONNECTOR Removal

48. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY Removal

49. REMOVE LAP BELT OUTER ANCHOR COVER

HINT
Follow the same procedures as for the opposite side.

(a) Disengage the 3 claws and remove the lap belt outer anchor cover.

50. REMOVE CENTER PILLAR LOWER GARNISH LH

(a) Remove the bolt and floor anchor of the front seat outer belt.

(b) Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish.

51. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT
Follow the same procedures as for the center pillar lower garnish LH.

52. REMOVE CENTER PILLAR UPPER GARNISH LH

(a) Remove the 2 screws.

(b) Disengage the clip and remove the center pillar upper garnish.

53. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT
Follow the same procedures as for the center pillar upper garnish LH.

54. REMOVE LUGGAGE COMPARTMENT SIDE TRAY LH

(a) Remove the 3 bolts.

(b) Disengage the 8 claws and 3 clips, and remove the luggage compartment side tray.

55. REMOVE REAR SEAT BACK CENTER HINGE SUB-ASSEMBLY Removal

56. REMOVE LUGGAGE COMPARTMENT SIDE TRAY RH

(a) w/ Woofer:

(1) Remove the bolt.

(2) Disengage the 5 claws and 7 clips, and remove the luggage compartment side tray.

(b) w/o Woofer:

(1) Remove the 3 bolts.

(2) Disengage the 5 claws and 5 clips, and remove the luggage compartment side tray.

57. REMOVE QUARTER TRIM LOWER PANEL LH

(a) Disengage the 2 claws and 2 clips, and remove the quarter trim lower panel.

58. REMOVE QUARTER TRIM LOWER PANEL RH

HINT
Follow the same procedures as for the quarter trim lower panel LH.

59. REMOVE QUARTER INSIDE TRIM BOARD LH

(a) Remove the bolt and remove the floor anchor of the rear seat belt outer.

HINT
Follow the same procedures as for the opposite side.

(b) Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.

Text in Illustration

(d) Disengage the 2 clips and remove the quarter inside trim board.

60. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT
Follow the same procedures as for the quarter inside trim board LH.

61. REMOVE ROOM LIGHT ASSEMBLY

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.

Text in Illustration

(b) Using a screwdriver with its tip taped in protective tape, disengage the 3 claws.

Text in Illustration

(c) Disconnect the room light connector and remove the room light.

62. REMOVE ROOF CONSOLE BOX ASSEMBLY

(a) Remove the screw.

(b) Disengage the 2 clips and 3 claws.

(c) Disconnect the connectors and remove the roof console box assembly.

(d) Using a clip remover, remove the wire harness clamp.

63. REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT
Follow the same procedures as for the opposite side.

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.

Text in Illustration

(b) Remove the 2 screws and assist grip.

64. REMOVE ASSIST GRIP PLUG (w/ Curtain Shield Airbag)

HINT
Follow the same procedures as for the opposite side.

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.

Text in Illustration

(b) Remove the screw.

(b) Remove the visor from the visor holder.

66. REMOVE VISOR ASSEMBLY RH

HINT
Follow the same procedures as for the visor assembly LH.

67. REMOVE VISOR HOLDER

(a) Turn the visor holder 90° counterclockwise and remove it.

HINT
Follow the same procedures as for the opposite side.

68. REMOVE COAT HOOK

HINT
Follow the same procedures as for the opposite side.

(a) Turn the coat hook 90° counterclockwise and remove it.

69. REMOVE ROOF HEADLINING ASSEMBLY

(a) Disconnect the 3 roof wire connector.

(b) Using a clip remover, remove the wire harness clamps.

(c) Remove the roof headlining from the vehicle.

70. REMOVE ROOF HEADLINING PAD

(a) Remove the 2 roof headlining pads from the roof headlining.

71. REMOVE ROOF WIRE

(a) w/ Vanity light:

(1) Remove the 20 tapes and roof wire.

(b) w/o Vanity Light:

(1) Remove the 9 tapes and roof wire.