Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2012 >> Tacoma PreRunner V6-4.0L (1GR-FE) >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Information Bus >> Testing and Inspection >> Component Tests and General Diagnostics >> Check CAN Bus Lines for Short Circuit

Check CAN Bus Lines for Short Circuit





CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Check CAN Bus Lines for Short Circuit
- Check CAN Bus Lines for Short Circuit

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ohms.





* *1: for Hydraulic Booster Type

* *2: for Vacuum Booster Type

WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
* Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
* Turn the ignition switch off before inspecting CAN bus wires for a ground short.
* After the ignition switch is turned off, check that the key reminder warning system is not in operation.
* Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT
* Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
* Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Service Precautions.

NEXT -- Continue to next step.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

(a) Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NEXT -- Continue to next step.

3. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

(a) Disconnect the J19 No. 1 CAN junction connector connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK -- Continue to next step.

4. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

(a) Disconnect the J18 No. 2 CAN junction connector connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- CONNECT CONNECTOR
OK -- Continue to next step.

6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - SKID CONTROL ECU)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





Result





B -- CONNECT CONNECTOR

C -- CONNECT CONNECTOR
A -- Continue to next step.

7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- CONNECT CONNECTOR

OK -- REPLACE NO. 2 CAN JUNCTION CONNECTOR

8. CONNECT CONNECTOR

(a) Reconnect the J18 No. 2 CAN junction connector connector.

NEXT -- Continue to next step.

9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

(a) Disconnect the J19 No. 1 CAN junction connector connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK -- Continue to next step.

10. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- CONNECT CONNECTOR
OK -- Continue to next step.

11. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- CONNECT CONNECTOR
OK -- Continue to next step.

12. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - YAW RATE AND DECELERATION SENSOR)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- CONNECT CONNECTOR
OK -- Continue to next step.

13. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ECM)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





Result





B -- CONNECT CONNECTOR

C -- CONNECT CONNECTOR

A -- REPLACE NO. 1 CAN JUNCTION CONNECTOR

14. CONNECT CONNECTOR

(a) Reconnect the J18 No. 2 CAN junction connector connector.

NEXT -- Continue to next step.

15. CHECK FOR SHORT IN CAN BUS WIRES (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))

(a) Disconnect the S1 master cylinder solenoid (skid control ECU) connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) Disassembly

16. CONNECT CONNECTOR

(a) Reconnect the J18 No. 2 CAN junction connector connector.

NEXT -- Continue to next step.

17. CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))

(a) Disconnect the S1 brake actuator assembly (skid control ECU) connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Removal

18. CONNECT CONNECTOR

(a) Reconnect the J18 No. 2 CAN junction connector connector.

NEXT -- Continue to next step.

19. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

(a) Disconnect the C9 combination meter assembly connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE COMBINATION METER ASSEMBLY Removal

20. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

21. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

(a) Disconnect the S9 steering angle sensor connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE STEERING ANGLE SENSOR Removal

22. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

23. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)

(a) Disconnect the A21 center airbag sensor assembly connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

24. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

25. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE AND DECELERATION SENSOR)

(a) Disconnect the Y1 yaw rate and deceleration sensor connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE YAW RATE AND DECELERATION SENSOR Removal

26. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

27. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

(a) Disconnect the E14 ECM connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE ECM Removal

28. CONNECT CONNECTOR

(a) Reconnect the J19 No. 1 CAN junction connector connector.

NEXT -- Continue to next step.

29. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

(a) Disconnect the E7 ECM connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)

OK -- REPLACE ECM Removal
pro multis · About Operation CHARM