Replacement

1GR-FE LUBRICATION: OIL AND OIL FILTER: REPLACEMENT

CAUTION:
* Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
* Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
* In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.
1. REMOVE NO. 1 ENGINE UNDER COVER

(a) Remove the 3 screws and 5 bolts.

(b) Unhook the engine under cover from the vehicle body as shown in the illustration.

2. DRAIN ENGINE OIL

(a) Remove the oil filler cap.

(b) Remove the oil pan drain plug and drain the engine oil into a container.

(c) Install a new gasket and the oil pan drain plug.

Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)

3. REMOVE OIL FILTER ELEMENT

(a) Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

Text in Illustration

(b) Remove the oil filter drain plug.

NOTICE:
If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

HINT
Use a container to catch the draining oil.

(d) Check that oil is drained from the oil filter. Then, disconnect the pipe as shown in the illustration and remove the O-ring.

(e) Using SST, remove the oil filter cap.

SST : 09228-06501

Text in Illustration

NOTICE:
Do not remove the oil filter bracket clip.

(f) Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration

NOTICE:
Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.

4. INSTALL OIL FILTER ELEMENT

(a) Clean the inside of the oil filter cap, the threads and O-ring groove.

(b) Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.

(c) Set a new oil filter element on the oil filter cap.

(d) Remove any dirt or foreign matter from the installation surface of the engine.

(e) Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

(f) Using SST, tighten the oil filter cap.

SST : 09228-06501

Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)

Text in Illustration

NOTICE:
* When tightening the oil filter cap, do not remove the oil filter bracket clip.
* Make sure that the oil filter is installed securely as shown in the illustration.
* Make sure that the O-ring does not get caught between the parts.

(g) Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

Text in Illustration

NOTICE:
Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

(h) Install the oil filter drain plug.

Torque : 13 Nm (127 kgf-cm, 9 ft-lbf)

NOTICE:
Make sure that the O-ring does not get caught between the parts.

5. ADD ENGINE OIL

(a) Add fresh oil.

Standard Oil Grade:

Standard Oil Capacity:

6. CHECK ENGINE OIL LEVEL Testing and Inspection

7. INSPECT FOR ENGINE OIL LEAK

(a) Start the engine. Make sure that there are no oil leaks from the area that was worked on.

8. INSTALL NO. 1 ENGINE UNDER COVER

(a) Hook the engine under cover to the vehicle body as shown in the illustration.

(b) Install the 3 screws and 5 bolts.

for bolt - Torque : 29 Nm (296 kgf-cm, 21 ft-lbf)

for screw - Torque : 3.0 Nm (31 kgf-cm, 27 in-lbf)