Sun Shade
Sun Shade
1 Glide Piece
• Inserted sideways on sun shade.
2 Sun Shade with Automatic Retractor
• The sunroof crossmember is removed.
Sun shade is pre-tensioned by a spring and must be secured against unwinding before removing => [ Anti-twist element for sun shade ]
• Remove the adjusting clip from the axle before removing
• To remove, slide roller to the side - in direction of arrow -.
• The shade can only be inserted into the side that has the clip, which must be removed beforehand
• Secure axle from unwinding using a piece of wire and lift out sun shade on one side.
• Remove sun shade out of guides with sliders set off to the sides.
• For the front sun shade, roller must be slid in opposite direction of arrow.
3 Roof Module
4 Screw
5 Catches
Anti-twist element for sun shade
Sun shade is pre-tensioned by a spring and must be secured against unwinding before removing => [ Anti-twist element for sun shade ]
- Bring hole, located in axle and in shaft, into alignment by sliding sideways after removing the clip.
- Lock axle and shaft - 3 - using a thin piece of wire - 4 - and secure it so that sun shade does not unwind.
- Now sun shade can be removed from roof module.
- If glide pieces - 1 - remain in guides, they must be removed and reinserted again before installing sun shade - 2 -
Front sun shade, removing
- Headliner lowered.
- Remove the sunroof crossmember.
- Push the adjusting clip- 1 - with the pin for securing the spring through hose in the axle - 2 - in direction of arrow.
Be careful not to damage the paint when unlocking the gliding piece. Use adhesive tape in this area.
- Remove the gliding piece - 2 - on both sides in - direction of arrow -from the sun shade arch - 1 - with a screwdriver.
- Remove the sun shade arch - 1 - from the gliding piece - 2 - in - direction of arrow -.
Remove the sun shade arch - 1 - from the gliding piece - 2 - in direction of arrow.
- Remove the clip - 1 - from the axle opposite direction of - arrow -.
- Install the shade - arrow A - and align both holes - arrow B - in the axle and in the shaft.
- Secure the shade from rotating with a wire pin as illustrated and remove the shade.
Installing the front sun shade
- Insert the flat axle - arrow - on the shade into the roof.
- Insert the other end in to the mount on the opposite side.
- Install the clip on the axle with pliers after installing the shade.
- The illustration show the clip in the correct position.
• It is now not possible to slide the shade - 2 - from side to side.
- Position the sun shade arch - arrow - on the gliding piece.
- Install the sun shade arch into the sun shade arch in direction of - arrow -.
- When installing - arrow A -, the sun shade arch - 1 - must fit completely into the gliding piece - 2 - and lock - arrow B -.
Removing the gliding piece
- Slide the sun shade arch to the rear and remove it from the guides after removing the sun shade arch.
• The illustration shows the gliding piece from inside the vehicle.
Rear sun shade, removing
- Headliner lowered.
- Remove the sunroof crossmember.
- Push the adjusting clip- 1 - with the pin for securing the spring through hose in the axle in direction of - arrow -.
- Remove the sun shade arch from the guides on the sunroof as illustrated.
- Install the shade - arrow A - and align both holes - arrow B - in the axle and in the shaft.
- Secure the shade from rotating with a wire pin as illustrated and remove the shade.
Installing the rear sun shade
- To install, perform the steps used in removal in reverse order.
- Install the clip on the axle with pliers after installing the sun shade.
- The illustration show the clip in the correct position.
• It is now not possible to slide the shade - 2 - from side to side.
Sunroof crossmember
1 Cross Member for Sunroof
• The headliner is just lowered and not removed.
• To remove, remove bolts - 2 -.
• Connecting parts at left - 3 - and right - 5 - remain in the vehicle.
2 Bolts
• 7 Nm
3 Left Connecting Part
4 Bolt
• 3.5 Nm
5 Right Connecting Part
6 Headliner
• Lower but do not remove
7 Rear Sun Shade
8 Front Sun Shade