Operation CHARM: Car repair manuals for everyone.

Powertrain Management




DTC P0106

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0106
- Manifold Absolute Pressure (MAP) Sensor Performance

Diagnostic Fault Information






Typical Scan Tool Data






Circuit Description

The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.

* The throttle model describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP. The information from this model is displayed on the scan tool as the MAF Performance Test parameter.

* The first intake manifold model describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model. The information from this model is displayed on the scan tool as the MAP Performance Test 1 parameter.

* The second intake manifold model is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input. The information from this model is displayed on the scan tool as the MAP Performance Test 2 parameter.

* The fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model. The information from this model is displayed on the scan tool as the TP Performance Test parameter.

The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.






Conditions for Running the DTC

* DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0128, P0335, P0336 are not set.

* The engine is running.

* The IAT sensor is between -7 and +125°C (+19 and +257°F).

* The ECT sensor is between 70-125°C (158-257°F).

* This DTC runs continuously when the above conditions are met.

Conditions for Setting the DTC

The engine control module (ECM) detects that the MAP sensor pressure is not within range of the calculated pressure that is derived from the system of models for more than 0.5 s.

Action Taken When the DTC Sets

DTC P0106 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0106 is a Type B DTC.

Diagnostic Aids

* A skewed or stuck engine coolant temperature (ECT) or IAT sensor will cause the calculated models to be inaccurate and may cause this DTC to run when it should not. Refer to Temperature Versus Resistance Temperature Versus Resistance.

* The BARO that is used by the ECM to calculate the air flow models is initially based on the MAP sensor at ignition ON. When the engine is running, the ECM will continually update the BARO value near wide open throttle using the MAP sensor and a calculation. A skewed MAP sensor will cause the BARO value to be inaccurate. Use the scan tool and compare the BARO parameter at ignition ON to the Altitude vs. Barometric Pressure Table. Refer to Altitude Versus Barometric Pressure Altitude Versus Barometric Pressure.

* A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions.

* Inspect for the following conditions:

- Incorrect CAM timing-Refer to Timing Chain, Crankshaft Sprocket, Camshaft Position Actuator, and Solenoid Valve Replacement Service and Repair for the correct timing.

- Worn piston rings-Refer to Engine Compression Test Testing and Inspection.

Reference Information

Schematic Reference

Engine Controls Schematics (LZ1) [1][2]Electrical Diagrams

Connector End View Reference

Component Connector End Views 1-2 Shift Solenoid (SS) Valve (M30)

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References Control Module References for scan tool information

Special Tools

* J-35555 - Metal Mityvac

* J-23738-A - Mityvac

Circuit/System Verification

1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description Hybrid Modes of Operation Description.

2. Ignition ON, verify the scan tool hood position parameter displays Open.

If the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle for DTC P254F.

3. If DTC P0641 or P0651 are set, refer to DTC P0641 or P0651 (ECM) Powertrain Management (ECM).

4. Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust Restricted Exhaust.

5. Verify that the engine is in good mechanical condition. Refer to Symptoms - Engine Mechanical Symptoms - Engine Mechanical.

6. Ignition OFF for 90 s or until the ECM powers down, determine the current vehicle testing altitude.

7. Ignition ON, observe the scan tool BARO Sensor parameter. Compare the parameter to the Altitude Versus Barometric Pressure Altitude Versus Barometric Pressure table. The BARO sensor pressure parameter should be within the specified range indicated in the table.

Note: A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements.

8. Compare the MAP Sensor parameter with a scan tool to a known good vehicle under various operating conditions. The readings should be within 3 kPa of the known good vehicle.

9. Ignition ON, observe the scan tool MAP sensor parameter. Start the engine. The MAP Sensor parameter should change.

10. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: All electrical components and accessories must be turned OFF and allowed to power down.

1. Verify the integrity of the air induction system by inspecting for the following conditions:

* Any damaged components

* Loose or improper installation

* Improperly routed vacuum hoses

* Any vacuum leak

* Any type of restriction

* MAP sensor seal that is missing or damaged

2. Verify that restrictions do not exist in the MAP sensor vacuum source.

3. Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust Restricted Exhaust.

4. Ignition OFF, disconnect the harness connector at the MAP sensor.

5. Ignition OFF for 90 s or until the ECM powers down, test for less than 5 ohms between the low reference circuit terminal 2 and ground.

If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

6. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.

If less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

7. Verify the scan tool MAP Sensor parameter is less than 12 kPa.

If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

8. Install a 3 A fused jumper wire between the signal circuit terminal 3 and the 5 V reference circuit terminal 1. Verify the scan tool MAP Sensor parameter is greater than 103 kPa.

If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

9. If all circuits test normal, test or replace the MAP sensor.

Component Testing

Important: You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing.


Skewed Sensor Test

1. Using the following steps and referencing the table below will determine if the MAP sensor is skewed.

2. Ignition ON, engine OFF, observe the MAP sensor scan tool parameter.

3. Use the observed MAP Sensor Scan Tool parameter that is closest to a value that is indicated in the first column.

4. Using the J-23738-A - mityvac or the J-35555 - metal mityvac to apply 5 in Hg of vacuum to the MAP sensor, the parameter in the first column should decrease by 17 kPa. The acceptable range is indicated in the second column.

5. Using the J-23738-A - mityvac or the J-35555 - metal mityvac to apply 10 in Hg of vacuum to the MAP sensor, the parameter in the first column should decrease by 34 kPa. The acceptable range is indicated in the third column.





Erratic Signal Test

1. Ignition OFF, remove the MAP sensor.

2. Install a 3 A fused jumper wire between the 5 V reference circuit terminal C and the corresponding terminal of the MAP sensor.

3. Install a jumper wire between the low reference terminal 2 of the MAP sensor and ground.

4. Connect a DMM between the MAP sensor circuit terminal 3 and ground.

5. Ignition ON, with the J-23738-A - mityvac or the J-35555 - metal mityvac , slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 4.9-5.2 V without any spikes or dropouts.

If the voltage is erratic, replace the MAP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.

* Manifold Absolute Pressure Sensor Replacement Service and Repair

* Control Module References Control Module References for ECM replacement, setup, and programming