Inspection
CYLINDER BLOCK
Inspection
CRANKSHAFT END PLAY
- Measure the clearance between thrust bearings and crankshaft arm when crankshaft is moved fully forward or backward with a dial indicator.
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, replace thrust bearings, and measure again. If it still exceeds the limit, replace crankshaft also.
CONNECTING ROD SIDE CLEARANCE
- Measure the side clearance between connecting rod and crankshaft arm with a feeler gauge.
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, replace connecting rod, and measure again. If it still exceeds the limit, replace crankshaft also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
Measure the inner diameter of piston pin hole with an inside micrometer (A).
Standard : Refer to "Cylinder Block" Cylinder Block.
Piston Pin Outer Diameter
Measure the outer diameter of piston pin with a micrometer (A).
Standard : Refer to "Cylinder Block" Cylinder Block.
Piston to Piston Pin Oil Clearance
(Piston to piston pin oil clearance) = (Piston pin hole diameter) � (Piston pin outer diameter)
Standard : Refer to "Cylinder Block" Cylinder Block.
- If the calculated value is out of the standard, replace piston and piston pin assembly.
- When replacing piston and piston pin assembly, Description.
NOTE:
- Piston is available together with piston pin as assembly.
- Piston pin (piston pin hole) grade is provided only for the parts installed at the plant. For service parts, no piston pin grades can be selected. (Only "0" grade is available.)
PISTON RING SIDE CLEARANCE
- Measure the side clearance of piston ring (1) and piston ring groove with a feeler gauge (C).
A : NG
B : OK
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, replace piston ring, and measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
- Check that the cylinder bore inner diameter is within the specification. Disassembly And Assembly, "Disassembly and
Assembly".
- Lubricate with new engine oil to piston (1) and piston ring (2), and then insert piston ring until middle of cylinder with piston, and measure the piston ring end gap with a feeler gauge (B).
A : Press-fit
C : Measuring point
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, replace piston ring, and measure again. If it still exceeds the limit, rebore cylinder and use oversize piston and piston rings.
CONNECTING ROD BEND AND TORSION
- Check with a connecting rod aligner.
A : Bend
B : Torsion
C : Feeler gauge
Bend limit : Refer to "Cylinder Block" Cylinder Block.
Torsion limit : Refer to "Cylinder Block" Cylinder Block.
- If it exceeds the limit, replace connecting rod assembly.
CONNECTING ROD BIG END DIAMETER
- Install connecting rod bearing cap without installing connecting rod bearing, and tightening connecting rod bolts to the specified torque. Disassembly And Assembly for the tightening procedure.
1 : Connecting rod
- Measure the inner diameter of connecting rod big end with an inside micrometer.
Standard : Refer to "Cylinder Block" Cylinder Block.
- If out of the standard, replace connecting rod assembly.
CONNECTING ROD BUSHING OIL CLEARANCE
Connecting Rod Bushing Inner Diameter
Measure the inner diameter of connecting rod bushing with an inside micrometer (A).
Standard : Refer to "Cylinder Block" Cylinder Block.
Piston Pin Outer Diameter
Measure the outer diameter of piston pin with a micrometer (A).
Standard : Refer to "Cylinder Block" Cylinder Block.
Connecting Rod Bushing Oil Clearance
(Connecting rod bushing oil clearance) = (Connecting rod bushing inner diameter) � (Piston pin outer diameter)
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the calculated value exceeds the limit, replace connecting rod assembly and/or piston and piston pin assembly.
- If replacing piston and piston pin assembly, Description.
- If replacing connecting rod assembly, refer to EM-135, "Connecting Rod Bearing" to select the connecting rod bearing.
A : Sample codes
B : Bearing stopper groove
C : Small-end diameter grade
D : Big-end diameter grade
E : Weight grade
F : Cylinder No.
G : Management code
H : Front mark
I : Management code
Factory installed parts grading:
- Service parts apply only to grade "0".
A : Piston grade number
B : Front mark
C : Piston pin grade number
CYLINDER BLOCK DISTORTION
- Using a scraper, remove gasket on the cylinder block surface, and also remove engine oil, scale, carbon, or other contamination.
CAUTION:
Be careful not to allow gasket flakes to enter engine oil or engine coolant passages.
- Measure the distortion on the cylinder block upper face at some different points in six directions (C), (D), (E), (F), (G), and (H) with a straightedge (A) and a feeler gauge (B).
Limit : Refer to "Cylinder Block" Cylinder Block.
- If it exceeds the limit, replace cylinder block.
MAIN BEARING HOUSING INNER DIAMETER
- Install lower cylinder block (2) without installing main bearings, and tighten lower cylinder block bolts to the specified torque. Refer to
Disassembly And Assembly for the tightening procedure.
- Measure the inner diameter of main bearing housing with a bore gauge.
Standard : Refer to "Cylinder Block" Cylinder Block.
- If out of the standard, replace cylinder block (1) and lower cylinder block as assembly.
NOTE:
Cylinder block cannot be replaced as a single part, because it is machined together with lower cylinder block.
PISTON TO CYLINDER BORE CLEARANCE
Cylinder Bore Inner Diameter
- Using a bore gauge, measure cylinder bore for wear, out-of-round and taper at six different points on each cylinder. [(A) and (B) directions at (C), (D) and (E)] is in longitudinal direction of engine.
f : 10 mm (0.39 in)
g : 60 mm (2.36 in)
h : 125 mm (4.92 in)
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, or if there are scratches and/or seizure on the cylinder inner wall, hone or rebore the inner wall.
- Oversize piston is provided. When using oversize piston, rebore cylinder so that the clearance of the piston to cylinder bore satisfies the standard.
CAUTION:
When using oversize piston, use oversize pistons for all cylinders with oversize piston rings.
Oversize (O/S) : 0.2 mm (0.008 in)
Piston Skirt Diameter
Measure the outer diameter of piston skirt with a micrometer (A).
Measure point Standard : Refer to "Cylinder Block" Cylinder Block.
Piston-to-Cylinder Bore Clearance
Calculate by piston skirt diameter and cylinder bore inner diameter
[direction (B), position (D)].
A : Longitudinal direction
C : Top position
E : Bottom position
f : 10 mm (0.39 in)
g : 60 mm (2.36 in)
h : 125 mm (4.92 in)
(Clearance) = (Cylinder bore inner diameter) � (Piston skirt diameter).
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If the calculated value exceeds the limit, replace piston and piston pin assembly. Cylinder Block, "Cylinder Block".
Re-boring Cylinder Bore
1. Cylinder bore size is determined by adding piston to cylinder bore clearance to piston skirt diameter.
Re-bored size calculation: D = A + B ? C
where,
A: Piston skirt diameter as measured
B: Piston to cylinder bore clearance (standard value)
C: Honing allowance 0.02 mm (0.0008 in)
D: Bored diameter
2. Install lower cylinder block, and tighten to the specified torque. Otherwise, cylinder bores may be distorted in final assembly.
3. Cut cylinder bores.
NOTE:
- When any cylinder needs boring, all other cylinders must also be bored.
- Do not cut too much out of cylinder bore at a time. Cut only 0.05 mm (0.0020 in) or so in diameter at a time.
4. Hone cylinders to obtain the specified piston to cylinder bore clearance.
5. Measure finished cylinder bore for the out-of-round and taper.
NOTE:
Measurement should be done after cylinder bore cools down.
CRANKSHAFT MAIN JOURNAL DIAMETER
- Measure the outer diameter of crankshaft main journals with a micrometer.
Standard : Refer to "Cylinder Block" Cylinder Block.
- If out of the standard, measure the main bearing oil clearance. Then use undersize bearing. EM-
137, "Main Bearing".
CRANKSHAFT PIN JOURNAL DIAMETER
- Measure the outer diameter of crankshaft pin journal with a micrometer (A).
Standard : Refer to "Cylinder Block" Cylinder Block.
- If out of the standard, measure the connecting rod bearing oil clearance. Then use undersize bearing. Connecting Rod Bearing, "Connecting Rod Bearing".
CRANKSHAFT OUT-OF-ROUND AND TAPER
- Measure the dimensions at four different points as shown in the figure on each main journal and pin journal with a micrometer.
- Out-of-round is indicated by the difference in the dimensions between (d) and (c) at (a) and (b).
- Taper is indicated by the difference in the dimensions between.
Limit : Refer to "Cylinder Block" Cylinder Block.
- If the measured value exceeds the limit, correct or replace crankshaft.
- If corrected, measure the bearing oil clearance of the corrected main journal and/or pin journal. Then select the main bearing and/or connecting rod bearing. Service and Repair and/or Connecting Rod Bearing.
CRANKSHAFT RUNOUT
- Place V-block on precise flat table, and support the journals on the both end of crankshaft.
- Place a dial indicator straight up on the No. 3 journal.
- While rotating crankshaft, read the movement of the pointer on a dial indicator. (Total indicator reading)
Standard and limit : Refer to "Cylinder Block" Cylinder Block.
- If it exceeds the limit, replace crankshaft.
CONNECTING ROD BEARING OIL CLEARANCE
Method by Calculation
- Install connecting rod bearings (1) to connecting rod (2) and connecting rod cap, and tighten connecting rod bolts to the specified torque. Disassembly And Assembly for the tightening procedure.
- Measure the inner diameter of connecting rod bearing with an inside micrometer.
(Oil clearance) = (Connecting rod bearing inner diameter) � (Crankshaft pin journal diameter)
Standard and limit : Refer to "Connecting Rod Bearing" Connecting Rod Bearing.
- If the calculated value exceeds the limit, select proper connecting rod bearing according to connecting rod big end diameter and crankshaft pin journal diameter to obtain the specified bearing oil clearance. Description.
Method of Using Plastigage
- Remove oil and dust on crankshaft pin journal and the surfaces of each bearing completely.
- Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil holes.
- Install connecting rod bearings to connecting rod and connecting rod bearing cap, and tighten connecting rod bolts to the specified torque. Disassembly And Assembly for the tightening procedure.
CAUTION:
Never rotate crankshaft.
- Remove connecting rod bearing cap and bearings, and using the scale on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is same as that described in the "Method by Calculation".
MAIN BEARING OIL CLEARANCE
Method by Calculation
- Install main bearings (3) to cylinder block (1) and lower cylinder block (2), and tighten lower cylinder block bolts to the specified torque. Disassembly And Assembly for the tightening procedure.
- Measure the inner diameter of main bearing with a bore gauge.
(Oil clearance) = (Main bearing inner diameter) � (Crankshaft main journal diameter)
Standard and limit : Refer to "Main Bearing" Main Bearing.
- If the calculated value exceeds the limit, select proper main bearing according to main bearing inner diameter and crankshaft main journal diameter to obtain the specified bearing oil clearance.
Description.
Method of Using Plastigage
- Remove engine oil and dust on crankshaft journal and the surfaces of each bearing completely.
- Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil holes.
- Install main bearing to cylinder block and lower cylinder block, and tighten lower cylinder block bolts with lower cylinder block to the specified torque. Disassembly And Assembly for the tightening procedure.
CAUTION:
Never rotate crankshaft.
- Remove lower cylinder block and bearings, and using the scale on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is same as that described in the "Method by Calculation".
MAIN BEARING CRUSH HEIGHT
- When lower cylinder block is removed after being tightened to the specified torque with main bearings (1) installed, the tip end of bearing must protrude. Disassembly And Assembly for the tightening procedure.
A : Crush height
Standard : There must be crush height.
- If the standard is not met, replace main bearings.
CONNECTING ROD BEARING CRUSH HEIGHT
- When connecting rod bearing cap is removed after being tightened to the specified torque with connecting rod bearings (1) installed, the tip end of bearing must protrude. Disassembly And Assembly for the tightening procedure.
A : Crush height
Standard : There must be crush height.
- If the standard is not met, replace connecting rod bearings.
LOWER CYLINDER BLOCK BOLT OUTER DIAMETER
- Measure the outer diameters (c), (d) at two positions as shown in the figure.
a : 20 mm (0.79 in)
b : 30 mm (1.18 in)
e : 10 mm (0.39 in)
- If reduction appears in (a) range, regard it (c).
Limit [(d) - (c)] : 0.11 mm (0.0043 in)
- If it exceeds the limit (large difference in dimensions), replace lower cylinder block bolt with new one.
CONNECTING ROD BOLT OUTER DIAMETER
1. Measure the outer diameters [(a), (b) and (c)] at the position shown in the figure.
a : Value at the end of the smaller diameter of the bolt
b : Value at the end of the smaller diameter of the bolt [opposite side of (a)]
c : Value of the smallest diameter of the smaller of the bolt
2. Obtain a mean value (d) of (a) and (b).
3. Subtract (c) from (d).
Limit [(d) - (c)] : 0.09 mm (0.0035 in)
4. If it exceeds the limit (large difference in dimensions), replace the bolt with new one.
DRIVE PLATE
- Check drive plate and signal plate for deformation or damage.
CAUTION:
- Never disassemble drive plate.
- Never place drive plate with signal plate facing down.
- When handling signal plate, take care not to damage or scratch it.
- Handle signal plate in a manner that prevents it from becoming magnetized.
- If anything is found, replace drive plate.
OIL JET
- Check nozzle for deformation and damage.
- Blow compressed air from nozzle, and check for clogs.
- If it is not satisfied, clean or replace oil jet.
OIL JET RELIEF VALVE
- Using a clean plastic stick, press check valve in oil jet relief valve.
Check that valve moves smoothly with proper reaction force.
- If it is not satisfied, replace oil jet relief valve.