Operation Check

DOOR LOCK: WIRELESS DOOR LOCK CONTROL SYSTEM: OPERATION CHECK

OPERATION CHECK

1. FUNCTIONS AND OPERATING CONDITIONS
(a) Wireless door lock/unlock function:
The wireless door lock control function operates only when the following 3 conditions are met:
(1) No key is inserted in the ignition key cylinder.
(2) All the doors are closed.
(3) The power door lock system operates normally.
HINT: The unlock function operates even when a door is open.

(b) Power back door open function:
The wireless door lock control function operates only when the following 4 conditions are met:
(1) No key is inserted in the ignition key cylinder.
(2) The power back door OFF switch is ON (switch free: the state in which the switch is pressed).
(3) The back door is between the fully closed position and the half-open position (When the door is in the fully closed position, the door will be unlocked).
(4) The power back door system operates normally.
(c) Power back door close function:
The wireless door lock control function operates only when the following 4 conditions are met:
(1) No key is inserted in the ignition key cylinder.
(2) The power back door OFF switch is ON (switch free: the state in which the switch is pressed).
(3) The back door is between the half-open position and the fully open position.
(4) The power back door system operates normally.
(d) Remote panic function:
The wireless door lock control function operates only when the following condition is met:
(1) The ignition switch is turned off.
HINT: The key can be inserted, however it must be in the off position.

(e) The wireless door lock control operational range differs depending on the situation.
(1) The operational range differs depending on the user and the ways the transmitter is held.
(2) In certain areas, the remote control function will only operate partially for the operational range, which will be reduced due to the vehicle body shape and the influence of the surrounding environment.
(3) Since the transmitter uses weak radio waves, strong radio waves or noise in the frequency used by the transmitter may reduce the operational range and the remote control may not function.
(4) When the battery is low, the operational range is reduced and the remote control may not function.
HINT: If the door control transmitter has been left in a place that is exposed to direct sunlight, such as on the instrument panel, the battery may be weakened or other problems may occur.

2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
HINT:
- The switches built into the door control transmitter send radio waves to the door lock control receiver.
- The operational range must be taken into account during checks.

(a) Make sure that the vehicle is placed in conditions that allow the wireless control function to be operated.
(b) Check the following basic functions.
(1) Check whether the LED of the transmitter comes on 3 times when each switch is pressed 3 times.
HINT: If the LED does not illuminate when the switch has been pressed 3 times or more, the battery may be depleted.
(2) Check that all the doors lock when the LOCK switch is pressed.
(3) Check that only the driver side door unlocks when the UNLOCK switch is pressed once and that the other doors unlock when the UNLOCK switch is pressed again within 3 seconds.
(4) with Power back door:

- Check that the power back door opens or closes when the PWR DOOR switch has been held down for 0.8 seconds or more.
- Check that the power back door reverses immediately when the PWR DOOR switch is pressed again while the door is automatically moving (no delay).
(5) Check that all the power windows and the sliding roof (normal type only) open when the UNLOCK switch has been held down for 2.5 seconds or more and that they stop operation when the switch is released.
(c) Check the chattering prevention function.
(1) Check that the selected operation occurs only once and is not repeated continuously while the switch is held down. However, when the switch is operated repeatedly at 1 second intervals, check that the selected operation is carried out.
(d) Check the automatic locking function.
(1) Check that all the doors lock automatically as long as none of them has been opened or locked within approx. 30 seconds after they are unlocked by pressing the UNLOCK switch.
(2) Check that the automatic locking function does not operate when any door has been opened or all of them have been locked, within approx. 30 seconds after they are unlocked by pressing the UNLOCK switch.
(e) Check the switch operation fail-safe function.
(1) Check that the doors cannot be locked by the switch while the key is in the ignition key cylinder.
However, this does not apply when the system is in the recognition code registration mode.
(f) Check the door ajar warning function.
(1) Check that the doors are not locked by the switch while any door is open or not completely closed and the wireless door lock buzzer sounds for 10 seconds.
(g) Check the repeat function.
(1) Check that all the doors attempt to automatically lock once again 1 second after LOCK has been pressed while the movement of the driver side door control (lock/unlock) knob, which is in the unlocked state, is being restricted.
(h) Check the answer back function.
(1) When the LOCK switch is pressed, check that the hazard warning lights flash once and the buzzer sounds once simultaneously with the locking of all the doors.
(2) When the UNLOCK switch is pressed once, check that the hazard warning lights flash twice and the buzzer sounds twice simultaneously with the unlocking of the driver side door.
(3) When the UNLOCK switch has been pressed again within 3 seconds, check that the hazard warning lights flash twice and the buzzer sounds twice simultaneously with the unlocking of all the doors.
(4) When the UNLOCK switch is held down for 2.5 seconds or more, check that the buzzer sounds once and all the power windows and the sliding roof (normal type only) start opening.
(5) with Power back door:
When the PWR DOOR switch has been held down for 0.8 seconds or more, check that the buzzer sounds twice simultaneously with the operation of the power back door.
(i) Check the illuminated entry function.
(1) When all the doors are locked, pressing the UNLOCK switch causes the interior light (when the switch is in the DOOR position) to come on simultaneously with the unlock operation.
(2) Check that the interior light goes off in approx. 15 seconds if no door has been opened.
(j) Check the remote panic function.
(1) with Power back door:
Check that the horn sounds, the headlights and taillights flash for 60 seconds (the theft alarm function) when the LOCK (PANIC) switch is held down for 2.5 seconds or more. Also, check that the horn stops sounding and lights stop flashing when either switch of the transmitter is pressed.
(2) without Power back door:
Check that the horn sounds, the headlights and taillights flash for 60 seconds (the theft alarm function) when the PANIC switch is held down for 0.8 seconds or more. Check also that the horn stops sounding and the lights stop flashing when either switch of the transmitter is pressed.