Scan Tool Data Definitions (Disengage History)

Scan Tool Data Definitions (Disengage History)

The Cruise Control Scan Tool Definitions - Disengage History is a common list for all of the available cruise control disengagement definitions available on the scan tool. The cruise control system equipped on the vehicle determines which cruise control disengagement parameters are available on the scan tool.

One of the following conditions must be present in order for a disengagement parameter to appear:

* The cruise control system is active and disengagement is requested.
* The engagement of the cruise control system is requested while a fault is present.

Accel Rate
- The powertrain control module (PCM)/engine control module (ECM) detects that the vehicle acceleration is greater than the calibrated cruise control threshold.

Bad Sequence
- The PCM/ECM detects that a cruise control software execution error is present.

Brake
- The PCM/ECM detects that the stop lamps have been activated or the PCM/ECM detects that a stop lamp pedal activation had not occurred before the cruise control system was requested.

Cancel
- The PCM/ECM detects that the cruise control cancel switch has been activated.

CC Sw. Position
- The PCM/ECM detects that the acceleration mode is active without the activation of the Accel. switch.

Clutch
- The PCM/ECM detects that the clutch pedal switch has been activated.

Clutch Switch
- The PCM/ECM detects that the clutch pedal switch has been activated.

Cruise Off
- The PCM/ECM detects that the cruise On/Off switch was turned to OFF when the cruise control system was enabled.

Coast Low Speed
- The PCM/ECM detects that the Set/Coast switch is activated until the vehicle speed is below 37 km/h (23 mph).

Coast Disengage
- When the PCM/ECM detects that the cruise set/coast signal is active and the throttle blade fully closes the cruise control system will disengage until the PCM/ECM detects that the set/coast signal is inactive. The cruise control system will then engage and set with the new vehicle speed.

Decel Rate
- The PCM/ECM detects that the vehicle deceleration is greater than the calibrated cruise control threshold.

DTC Set
- The PCM/ECM detects that a DTC has been set which affects the cruise control operation.

Engine Run Time
- The PCM/ECM detects that the cruise control system has been requested and the engine run time counter is not active.

Engine Speed
- The PCM/ECM detects that the engine speed is less than or greater than a calibrated RPM.

ETC
- The PCM/ECM detects a fault within the throttle actuator control (TAC) system.

First Gear
- While the cruise control system is active, the PCM/ECM detects that the transmission is in Drive 1.

High Accel.
- The PCM/ECM detects that the vehicle acceleration is greater than the calibrated cruise control threshold.

High Decel.
- The PCM/ECM detects that the vehicle deceleration is greater than the calibrated cruise control threshold.

High Speed
- The PCM/ECM detects that the vehicle speed is greater than the calibrated amount.

Illegal Mode
- The PCM/ECM detects that the acceleration mode is active without the activation of the Accel. switch.

Injector Disable
- The PCM/ECM detects that the engine is overspeed and that the fuel shutoff has been activated.

Low Speed
- The PCM/ECM detects that the vehicle speed is less than 37 km/h (23 mph) while the cruise control system was enabled.

Low Voltage
- The PCM/ECM detects that the ignition voltage is below 9 volts.

Manual/Neutral
- The PCM/ECM detects that transmission is in Neutral, Reverse or Park.

Memory Corrupt
- An internal PCM/ECM memory fault is detected.

MPH Limit
- The PCM/ECM detects a that the vehicle is overspeed and that the fuel shutoff has been activated.

No History
- This parameter is displayed when a new PCM/ECM has been installed.

None
- This parameter is displayed when a new PCM/ECM has been installed.

Off
- The PCM/ECM detects that the cruise On/Off switch was turned to OFF when the cruise control system was enabled.

Over Set Speed
- This parameter is displayed when the current vehicle speed is greater than the set vehicle speed by more than a calibrated amount.

Over Speed
- This parameter is displayed when the current vehicle speed is greater than the set vehicle speed by more than a calibrated amount.

Over Speed Tap
- This parameter is displayed when the Set/Coast switch is briefly applied while the current vehicle speed is greater than the set vehicle speed by more than a calibrated amount.

Pedal Initialize
- The PCM/ECM detects that a stop lamp pedal activation had not occurred before the cruise control system was requested.

PCM Error
- The PCM/ECM detects that a cruise control software execution error is present.

PCM Inhibit
- The PCM/ECM detects a RAM corruption associated to the cruise control system.

Pedal > Cruise
- The PCM/ECM detects that the accelerator pedal overrides the set vehicle speed for approximately 60 seconds.

Serial Data
- A fault in the serial data circuit from the cruise control switch to the platform module is detected.

S/C On, CC Off
- When the PCM/ECM detects that the cruise set/coast signal is active and the throttle blade fully closes the cruise control system will disengage until the PCM/ECM detects that the set/coast signal is inactive. The cruise control system will then engage and set with the new vehicle speed.

S/C On - Speed High
- This parameter is displayed when the Set/Coast switch is briefly applied while the current vehicle speed is greater than the set vehicle speed by more than a calibrated amount.

Stop Lamp Switch
- The PCM/ECM detects that the stop lamps have been activated.

TAC Inhibit
- The PCM/ECM detects a fault within the TAC system.

Traction
- The PCM/ECM detects that the traction control system had been activated. It is also possible that a tire with low air pressure can also set this disengagement reason.

Traction Loss
- The PCM/ECM detects that the traction control system had been activated. It is also possible that a tire with low air pressure can also set this disengagement reason.

Two Commands
- The PCM/ECM detects that the Set/Coast switch and the Resume/Accel switch are active at the same time.

Two CC Commands
- The PCM/ECM detects that the Set/Coast switch and the Resume/Accel switch are active at the same time.

Under Speed
- The PCM/ECM detects that the vehicle speed is less than the cruise memory speed by more than a calibrated amount.

Under Set Speed
- The PCM/ECM detects that the vehicle speed is less than the cruise memory speed by more than a calibrated amount.