B1797

SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM: B1797: Calibration Malfunction

DTC B1797 - Calibration Malfunction

DESCRIPTION

DTC B1797 is output when one of the following conditions is met:

- Zero point calibration is performed when the conditions for the calibration are not satisfied.

- Zero point calibration has failed.

Condition for the Zero Point Calibration:









HINT: When DTC B1650 is stored as a result of troubleshooting for the "Airbag System", check the DTCs stored in the occupant classification ECU. When DTC B1797 is output, perform troubleshooting for it first.

INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC
(a) Turn the engine switch on (IG).
(b) Clear the DTCs stored in the occupant classification ECU. Initialization
(c) Clear the DTCs stored in the center airbag sensor. DTC Check / Clear
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG), and wait for at least 10 seconds.
(f) Check for DTCs. Reading and Clearing Diagnostic Trouble Codes
OK:
DTC B1797 is not output.
HINT: Codes other than DTC B1797 may be output at this time, but they are not related to this check.

NG -- READ VALUE USING TECHSTREAM (SPECIFIED CONDITION FOR ZERO POINT CALIBRATION)
OK -- USE SIMULATION METHOD TO CHECK
2. READ VALUE USING TECHSTREAM (SPECIFIED CONDITION FOR ZERO POINT CALIBRATION)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, read the "Data List". Scan Tool Testing and Procedures

Occupant Detection





Result





B -- REPLACE NO. 1 SEAT CUSHION ASSEMBLY (OCCUPANT DETECTION SENSOR)
A -- Continue to next step.
3. PERFORM ZERO POINT CALIBRATION
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, perform zero point calibration. Initialization
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG).
(f) Clear the DTCs stored in the memory. Reading and Clearing Diagnostic Trouble Codes
HINT: If the DTCs are not cleared at this time, past DTCs will remain.

NEXT -- Continue to next step.
4. CHECK FOR DTC
(a) Turn the engine switch on (IG).
(b) Clear the DTCs stored in the occupant classification ECU. Initialization
(c) Clear the DTCs stored in the center airbag sensor. DTC Check / Clear
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG).
(f) Check for DTCs. Reading and Clearing Diagnostic Trouble Codes
OK:
DTC B1797 is not output.
HINT: Codes other than DTC B1797 may be output at this time, but they are not related to this check.

NG -- REPLACE NO. 1 SEAT CUSHION ASSEMBLY (OCCUPANT DETECTION SENSOR)
OK -- END
5. REPLACE NO. 1 SEAT CUSHION ASSEMBLY (OCCUPANT DETECTION SENSOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, save the ECU data from the ECU which is installed in the vehicle. Registration
(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Replace the No. 1 seat cushion (occupant detection sensor).
(g) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(h) Turn the engine switch on (IG).
(i) Using the Techstream, load the previous ECU data stored in the Techstream into the new ECU. Registration
(j) Turn the engine switch off.
(k) Turn the engine switch on (IG).
(l) Clear the DTCs stored in the occupant classification ECU. Initialization
(m) Clear the DTCs stored in the center airbag sensor. Reading and Clearing Diagnostic Trouble Codes
NEXT -- Continue to next step.
6. PERFORM ZERO POINT CALIBRATION
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, perform zero point calibration. Initialization
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG).
(f) Clear the DTCs stored in the occupant classification ECU. Initialization
HINT: If the DTCs are not cleared at this time, past DTCs will remain.

NEXT -- Continue to next step.
7. PERFORM SENSITIVITY CHECK
(a) Perform the sensitivity check. Initialization
NEXT -- END