Installation

EXTERIOR: OUTSIDE MOULDING: INSTALLATION

INSTALLATION
HINT: The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.

1. INSTALL BACK DOOR OUTSIDE MOULDING RH

(a) Install 6 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the back door outside moulding will be improper.

(b) Engage the 6 clips and install the back door outside moulding.

(a) Install 6 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the back door outside moulding will be improper.

(b) Engage the 6 clips and install the back door outside moulding.

(c) Tighten the screw.
(d) Remove the protective tape.
3. INSTALL SPARE TIRE
Torque: 88 Nm (897 kgf-cm, 65 ft-lbf)
4. INSTALL ACCESS DOOR OUTSIDE MOULDING SUB-ASSEMBLY

(a) Install 4 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the access door outside moulding will be improper.

(b) Engage the 4 clips and install the access door outside moulding.

(c) Tighten the nut.
Torque: 5.0 Nm (50 kgf-cm, 44 in-lbf)
(d) Remove the protective tape.
5. INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

(a) Install 9 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the rear door outside moulding will be improper.

(b) Engage the 9 clips and install the front door outside moulding.

(c) Tighten the 2 nuts.
Torque: 5.0 Nm (50 kgf-cm, 44 in-lbf)
(d) Remove the protective tape.
6. INSTALL QUARTER PANEL MOULDING PAD
HINT: Only follow this procedure when replacing the quarter outside moulding pad.

(a) Install a new quarter outside moulding pad in the position shown in the illustration.
7. INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

(a) Install 2 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the quarter outside moulding will be improper.

(b) Engage the 2 clips and install the quarter outside moulding.

(e) Remove the protective tape.
8. INSTALL FRONT FENDER OUTSIDE MOULDING PAD
HINT: Only follow this procedure when replacing the front wheel opening extension pad.

(a) Install a new front wheel opening extension pad in the position shown in the illustration.
9. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY

(a) Install 2 new clips in the positions shown in the illustration.
NOTE: If you install the clips wrongly, the installation of the front fender moulding will be improper.

(b) Engage the 2 clips and install the front fender moulding.

(e) Remove the protective tape.
10. INSTALL FRONT BUMPER SIDE SUPPORT Installation
11. INSTALL ROCKER PANEL MOULDING
(a) Install 3 clips in the positions shown in the illustration.

NOTE: If you install the clips wrongly, the installation of the rocker panel moulding will be improper.

(b) Engage the 5 clips and install the rocker panel moulding.

12. INSTALL SIDE STEP SUB-ASSEMBLY Installation
13. INSTALL QUARTER PANEL MUDGUARD Installation
14. INSTALL FRONT FENDER MUDGUARD Installation
15. INSTALL REAR BUMPER COVER Installation
16. INSTALL FRONT BUMPER COVER

(a) Engage the 2 claws and install the front bumper cover.

(b) Tighten the 8 screws and the 4 bolts.
Torque: 3.0 Nm (30 kgf-cm, 27 in-lbf)
Torque: 8.0 Nm (80 kgf-cm, 71 in-lbf)

(d) Remove the protective tape.
17. INSTALL RADIATOR GRILLE Installation
18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Back Sonar)
Torque: 3.9 Nm (40 kgf-cm, 35 in-lbf)