Installation
WIPER AND WASHER: REAR WIPER MOTOR: INSTALLATION
1. PRECAUTION
NOTICE:
* Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.
* After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.
* If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.
2. INSTALL REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)
(a) Install the rear wiper motor assembly with the 4 bolts.
Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
NOTICE:
Be careful not to scratch the back door glass.
(b) Connect the connector.
3. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)
(a) Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.
NOTICE:
* Do not hold the rear wiper motor assembly by the rear wiper link pivot.
* Be careful not to scratch the back door glass.
* Do not remove the centering jig before installing the rear wiper link pivot.
(b) Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.
Bolt - Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
Nut - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
(c) Connect the connector.
4. INSTALL REAR WIPER MOTOR GROMMET (for Fixed Glass Type)
(a) Apply MP grease to the entire surface of the wiper motor grommet lip.
HINT
Make sure that the hole does not clog with grease and the grooves on the lip are filled with grease.
(b) Install the rear wiper motor grommet.
HINT
As shown in the illustration, install the rear wiper motor grommet with its position mark at the top.
5. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)
(a) Install the rear wiper link pivot with the nut.
Torque : 7.0 Nm (71 kgf-cm, 62 in-lbf)
(b) Open the glass hatch.
(c) Disengage the 2 guides.
(d) Disengage the 3 claws and remove the centering jig.
(e) Close the glass hatch.
6. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)
(a) Apply MP grease to the entire surface of the rear wiper link cap.
HINT
Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.
(b) Install the rear wiper link cap.
7. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Fixed Glass Type)
(a) Stop the wiper motor at the automatic stop position.
(b) When reinstalling:
(1) Clean the wiper arm serrations.
(2) Clean the wiper pivot serrations with a wire brush.
(c) Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
(d) Install the rear wiper arm and blade assembly with the nut.
Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
HINT
Hold down the wiper arm by hand when tightening the nut.
8. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)
(a) Stop the wiper motor at the automatic stop position.
(b) When reinstalling:
(1) Clean the wiper arm serrations.
(2) Clean the wiper pivot serrations with a wire brush.
(c) Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
(d) Install the rear wiper arm and blade assembly with the nut.
Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
HINT
Hold down the wiper arm by hand when tightening the nut.
9. INSTALL REAR WIPER ARM HEAD CAP
(a) Install the rear wiper arm head cap.
HINT
Push down on the cap until a click sound can be heard.
10. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)
(a) Open the glass hatch.
(b) Engage the 3 clips and install the rear wiper shaft cover.
(c) Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.
11. INSTALL BACK DOOR TRIM PANEL ASSEMBLY Reassembly
12. INSTALL ASSIST STRAP ASSEMBLY Reassembly
13. INSTALL ASSIST STRAP HOLE COVER Reassembly
14. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type) Reassembly
15. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door) Reassembly
16. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door) Reassembly
17. CONNECT POWER BACK DOOR ROD (w/ Power Back Door) Reassembly
18. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) Reassembly
19. INSTALL BACK DOOR TRIM COVER RH Reassembly
20. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY Reassembly