Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

1. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

(a) Align the matchmarks on the steering intermediate shaft sub-assembly and the steering column assembly.

(b) Install a new bolt.

Torque : 35 Nm (360 kgf-cm, 26 ft-lbf)

2. INSTALL STEERING COLUMN ASSEMBLY

(a) Check that the 2 bushings are securely installed to the steering column assembly.

HINT
If the bushings are missing or damaged, replace the steering column assembly with a new one.

(b) Install the steering column assembly with the bolt and 2 nuts.

Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)

(c) Connect the connectors and engage the wire harness clamps to the steering column assembly.

(d) Connect the connector to the power steering ECU assembly.

(e) Connect the connector to the power steering ECU assembly.

HINT
As shown in the illustration, securely return the lock lever to its original position to connect the connector.

3. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

(a) Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

(b) Install a new bolt.

Torque : 35 Nm (360 kgf-cm, 26 ft-lbf)

(c) Install the steering intermediate shaft sub-assembly to the steering column hole shield.

(d) Tighten the bolt.

4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

(a) Engage the 2 claws to install the No. 1 air duct sub-assembly.

5. POSITION FRONT WHEELS STRAIGHT AHEAD

6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

(a) Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

(b) Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

7. INSTALL STEERING COLUMN COVER

(a) Engage the claw to install the upper steering column cover.

(b) Engage the 2 claws to install the lower steering column cover.

Torque : 2.0 Nm (20 kgf-cm, 18 in-lbf)

8. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY Installation

9. INSTALL PUSH ROD PIN Installation

10. INSTALL BRAKE PEDAL RETURN SPRING Installation

11. INSTALL STOP LIGHT SWITCH ASSEMBLY Installation

12. INSPECT AND ADJUST BRAKE PEDAL HEIGHT Adjustments

13. INSPECT BRAKE PEDAL FREE PLAY Adjustments

14. INSPECT BRAKE PEDAL RESERVE DISTANCE Adjustments

15. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation

17. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH Installation

18. INSTALL FRONT DOOR SCUFF PLATE LH Installation

19. ADJUST SPIRAL CABLE Installation

20. INSTALL STEERING WHEEL ASSEMBLY Installation

21. INSTALL STEERING PAD Installation

22. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation

23. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation

24. INSTALL FRONT WHEEL LH

Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)

25. INSPECT STEERING WHEEL CENTER POINT

26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
* Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.
* Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.
* When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
27. INSPECT STEERING PAD Installation

28. INSPECT SRS WARNING LIGHT

HINT
Diagnosis System.