SRS Warning Light Remains ON
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: SRS Warning Light Remains ON
- SRS Warning Light Remains ON
DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. CHECK CAN COMMUNICATION SYSTEM
(a) Check if a CAN communication DTC is output Diagnosis System.
Result
B -- REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A -- Continue to next step.
2. CHECK BATTERY
(a) Measure the voltage of the battery.
Standard voltage:
11 to 14 V
NG -- CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK -- Continue to next step.
3. CHECK CONNECTOR
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and combination meter.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTOR
OK -- Continue to next step.
4. CHECK WIRE HARNESS (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR ASSEMBLY)
(a) Disconnect the E45 connector from the center airbag sensor.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Operate all components of the electrical system (defogger, wipers, headlight, heater blower, etc.).
(e) Measure the voltage of the wire harness side connectors.
Standard voltage:
(f) Turn the ignition switch off.
(g) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE WIRE HARNESS
OK -- Continue to next step.
5. CHECK WIRE HARNESS (SOURCE VOLTAGE OF COMBINATION METER)
(a) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(b) Disconnect the E19 connector from the combination meter.
(c) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(d) Turn the ignition switch to ON.
(e) Measure the voltage of the wire harness side connectors.
Standard voltage:
(f) Turn the ignition switch off.
(g) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE WIRE HARNESS
OK -- Continue to next step.
6. CHECK SRS WARNING LIGHT
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Connect the E19 connector to the combination meter.
(d) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(e) Turn the ignition switch to ON.
(f) Check the SRS warning light condition.
OK:
After the primary check period, SRS warning light goes off for approximately 10 seconds, and turning it on is continued.
HINT
The primary check period shows approximately 6 seconds after the ignition switch is turned to ON.
NG -- GO TO COMBINATION METER SYSTEM
OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY