Removal

INTERIOR: ROOF HEADLINING (for Access Cab): REMOVAL

1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Service Precautions.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

3. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

(a) Slide the inner rear view mirror cover in the direction indicated by the arrow in the illustration to disengage the 2 claws from the roof headlining, and then disengage the 2 claws of the inner rear view mirror cover from the mirror and remove the inner rear view mirror cover.

(b) Disconnect the connector.

4. REMOVE FRONT FLOOR FOOTREST Removal

5. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the 9 claws and clip, and remove the front door scuff plate.

6. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Follow the same procedures as for the front door scuff plate LH.

7. REMOVE COWL SIDE TRIM BOARD LH

(a) Remove the clip.

(b) Disengage the 2 clips and remove the cowl side trim board.

8. REMOVE COWL SIDE TRIM BOARD RH

HINT
Follow the same procedures as for the cowl side trim board LH.

9. REMOVE REAR DOOR SCUFF PLATE LH

(a) Disengage the 7 claws and remove the rear door scuff plate.

10. REMOVE REAR DOOR SCUFF PLATE RH

HINT
Follow the same procedures as for the rear door scuff plate LH.

11. REMOVE ROOF SIDE INNER GARNISH COVER LH

HINT
Follow the same procedures as for the opposite side.

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.

Text in Illustration

12. REMOVE ROOF SIDE INNER GARNISH COVER RH

HINT
Follow the same procedures as for the roof side inner garnish cover LH.

13. REMOVE ROOF SIDE INNER GARNISH CAP LH

(a) Using a "TORX" socket wrench T30, remove the 2 screws.

(b) Disengage the 4 claws and remove the roof side inner garnish cap.

14. REMOVE ROOF SIDE INNER GARNISH CAP RH

HINT
Follow the same procedures as for the roof side inner garnish cap LH.

15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the front door opening trim weatherstrip.

16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Follow the same procedures as for the front door opening trim weatherstrip LH.

17. REMOVE FRONT PILLAR GARNISH LH

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

Text in Illustration

HINT
Follow the same procedures as for the opposite side.

(b) Remove the 2 screws.

(1) Using a clip remover, remove the 3 wire harness clamps.

18. REMOVE FRONT PILLAR GARNISH RH

HINT
Follow the same procedures as for the front pillar garnish LH.

19. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) Removal

20. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) Removal

21. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY

(a) for Automatic Transmission:

(1) Remove the rear console upper panel sub-assembly Removal.

(b) for Manual Transmission:

(1) Remove the rear console upper panel sub-assembly Removal.

22. REMOVE REAR CONSOLE BOX ASSEMBLY Removal

23. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission) Removal

24. REMOVE FRONT CONSOLE BOX

(a) for Automatic Transmission:

(1) Remove the front console box Removal.

(b) for Manual Transmission:

(1) Remove the front console box Removal.

25. REMOVE AIR CONDITIONING CONTROL ASSEMBLY Removal

26. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET Removal

27. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY Disassembly

28. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL Removal

29. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

30. REMOVE COMBINATION METER ASSEMBLY Removal

31. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

32. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

33. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY Removal

34. REMOVE INSTRUMENT LOWER PANEL Removal

35. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY Removal

36. REMOVE INSTRUMENT SIDE PANEL Removal

37. DISCONNECT PASSENGER AIRBAG CONNECTOR Removal

38. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY Removal

39. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX

Removal

40. REMOVE REAR SEAT CUSHION ASSEMBLY

Removal

41. REMOVE BACK PANEL GARNISH HOLE PLUG

HINT
Follow the same procedure to remove all hole plugs.

(a) Disengage the 4 claws and remove the 2 back panel garnish hole plugs.

42. REMOVE BACK PANEL TRIM COVER

HINT
Follow the same procedure as for the opposite side.

(a) Disengage the 2 claws and the 2 guides, remove the back panel trim cover.

43. REMOVE BACK PANEL TRIM

(a) Remove the 2 clips.

(b) Disengage the 8 claws and 14 clips, and remove the back panel trim.

44. REMOVE QUARTER TRIM LOWER PANEL LH

(a) Remove the bolt and floor anchor of the rear seat belt outer.

(b) Disengage the claw and 2 clips, and remove the quarter trim lower panel.

45. REMOVE QUARTER TRIM LOWER PANEL RH

HINT
Follow the same procedures as for the quarter trim lower panel LH.

46. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 2 claws and clip, and remove the roof side inner garnish.

47. REMOVE ROOF SIDE INNER GARNISH RH

HINT
Follow the same procedures as for the roof side inner garnish LH.

48. REMOVE QUARTER INSIDE TRIM BOARD LH

(a) Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.

Text in Illustration

(b) Remove the screw.

(c) Disengage the 3 clips and remove the quarter inside trim board.

49. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT
Follow the same procedures as for the quarter inside trim board LH.

50. REMOVE ROOM LIGHT ASSEMBLY

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.

Text in Illustration

(b) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws.

Text in Illustration

(c) Disconnect the room light connector and remove the room light.

51. REMOVE ROOF CONSOLE BOX ASSEMBLY

(a) Remove the screw.

(b) Disengage the 2 clips and 3 claws.

(c) Disconnect the connectors and remove the roof console box assembly.

(d) Using a clip remover, remove the wire harness clamp.

52. REMOVE ASSIST GRIP PLUG

HINT
Follow the same procedures as for the opposite side.

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.

Text in Illustration

(b) Remove the screw.

(b) Remove the visor from the visor holder.

54. REMOVE VISOR ASSEMBLY RH

HINT
Follow the same procedures as for the visor assembly LH.

55. REMOVE VISOR HOLDER

HINT
Follow the same procedures as for the opposite side.

(a) Turn the visor holder 90° counterclockwise and remove it.

56. REMOVE COAT HOOK

HINT
Follow the same procedures as for the opposite side.

(a) Turn the coat hook 90° counterclockwise and remove it.

57. REMOVE ROOF HEADLINING ASSEMBLY

(a) Disconnect the 3 roof wire connectors.

(b) Using a clip remover, remove the wire harness clamps.

(c) Remove the roof headlining from the vehicle.

58. REMOVE ROOF HEADLINING PAD

(a) Remove the 2 roof headlining pads from the roof headlining.

59. REMOVE ROOF WIRE

(a) w/ Vanity light:

(1) Disconnect the 2 roof speaker connectors.

(2) Remove the 20 tapes and roof wire.

(b) w/o Vanity Light:

(1) Disconnect the 2 roof speaker connectors.

(2) Remove the 9 tapes and roof wire.