Installation
SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: INSTALLATION
1. INSTALL SPIRAL CABLE (w/o VSC)
(a) Check that the front wheels are facing straight ahead.
(b) Set the turn signal switch to the neutral position.
NOTICE:
If it is not in the neutral position, the turn signal switch pin may be snapped.
(c) Install the spiral cable with the 3 claws.
NOTICE:
When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.
(d) Connect the connectors to the spiral cable.
NOTICE:
When connecting the airbag connector, take care not to damage the airbag wire harness.
2. INSTALL SPIRAL CABLE (w/ VSC)
(a) Engage the 6 claws and 2 pins, and install the spiral cable to the steering angle sensor.
3. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR (w/ VSC)
(a) Check that the front wheels are facing straight ahead.
(b) Set the turn signal switch to the neutral position.
NOTICE:
If it is not in the neutral position, the turn signal switch pin may be snapped.
(c) Install the spiral cable with steering angle sensor with the 3 claws.
NOTICE:
When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.
(d) Connect the connectors to the spiral cable with steering angle sensor.
NOTICE:
When connecting the airbag connector, take care not to damage the airbag wire harness.
4. INSTALL UPPER STEERING COLUMN COVER Installation
5. INSTALL LOWER STEERING COLUMN COVER Installation
6. INSTALL HORN BUTTON WIRE SUB-ASSEMBLY (w/o Steering Pad Switch and Cruise Control System)
(a) Connect the connector and install the horn button wire sub-assembly.
7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation
8. INSTALL NO. 1 SWITCH HOLE BASE Installation
9. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle) Installation
10. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for Automatic Transaxle) Installation
11. INSTALL FRONT NO. 1 CONSOLE BOX INSERT Installation
12. INSTALL FRONT NO. 2 CONSOLE BOX INSERT Installation
13. INSTALL FRONT CONSOLE BOX ASSEMBLY (for 2WD) Installation
14. INSTALL FRONT CONSOLE BOX ASSEMBLY (for 4WD) Installation
15. INSTALL CONSOLE BOX CARPET
16. INSTALL NO. 2 SWITCH HOLE BASE Installation
17. INSTALL FRONT UPPER CONSOLE BOX Installation
18. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation
19. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Manual Transaxle) Installation
20. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Automatic Transaxle) Installation
21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) Installation
22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) Installation
23. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY Installation
24. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation
25. ADJUST SPIRAL CABLE
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Rotate the spiral cable counterclockwise slowly by hand until it stops.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
(d) Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
HINT
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
26. INSTALL STEERING WHEEL ASSEMBLY Installation
27. INSTALL STEERING PAD Installation
28. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation
29. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation
30. INSPECT STEERING WHEEL CENTER POINT
31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
32. INSPECT STEERING PAD Installation
33. INSPECT SRS WARNING LIGHT
(a) Inspect the SRS warning light Diagnosis System.