P0365
2AR-FE ENGINE CONTROL: SFI SYSTEM: P0365, P0367, P0368: Camshaft Position Sensor "B" Circuit (Bank 1)
DESCRIPTION
The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.
HINT
Reference: Inspection using an oscilloscope P0340.
MONITOR DESCRIPTION
If no pulse signal is transmitted by the camshaft position sensor for exhaust camshaft despite the camshaft revolving, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
All
P0365: Exhaust Camshaft Position Sensor Verify Pulse Input
P0367 and P0368: Exhaust Camshaft Position Sensor Range Check
TYPICAL MALFUNCTION THRESHOLDS
P0365: Exhaust Camshaft Position Sensor Verify Pulse Input
P0367: Exhaust Camshaft Position Sensor Range Check (Low Voltage)
P0368: Exhaust Camshaft Position Sensor Range Check (High Voltage)
COMPONENT OPERATING RANGE
CONFIRMATION DRIVING PATTERN
1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON and turn the Techstream on.
3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
4. Turn the ignition switch off and wait for at least 30 seconds.
5. Turn the ignition switch to ON and turn the Techstream on.
6. Start the engine.
7. Idle the engine for 10 seconds or more [A].
8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
9. Read the pending DTCs.
HINT
* If a pending DTC is output, the system is malfunctioning.
* If a pending DTC is not output, perform the following procedure.
10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
11. Input the DTC: P0365, P0367 or P0368.
12. Check the DTC judgment result.
HINT
* If the judgment result shows NORMAL, the system is normal.
* If the judgment result shows ABNORMAL, the system has a malfunction.
* If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.
13. If no pending DTC is output, perform a universal trip and check for permanent DTCs Reading and Clearing Diagnostic Trouble Codes.
HINT
* If a permanent DTC is output, the system is malfunctioning.
* If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
* If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
PROCEDURE
1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
(a) Disconnect the camshaft position sensor for exhaust camshaft connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
OK -- Continue to next step.
2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
(a) Disconnect the camshaft position sensor for exhaust camshaft connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
(a) Check the camshaft position sensor for exhaust camshaft installation.
OK:
Camshaft position sensor is installed correctly.
NG -- SECURELY REINSTALL CAMSHAFT POSITION SENSOR Installation
OK -- Continue to next step.
4. INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
(a) Check the timing rotor of the exhaust camshaft.
OK:
Camshaft timing rotor does not have any cracks or deformation.
HINT
Perform "Inspection After Repair" after replacing the exhaust camshaft Programming and Relearning.
NG -- REPLACE EXHAUST CAMSHAFT Removal
OK -- Continue to next step.
5. CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) P0011
NG -- ADJUST VALVE TIMING Reassembly
OK -- Continue to next step.
6. REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
(a) Replace the camshaft position sensor (for exhaust camshaft) Removal.
NEXT -- Continue to next step.
7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Start the engine.
(g) Turn the Techstream on.
(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(j) Read the DTCs.
Result
HINT
If the engine does not start, replace the ECM.
B -- END
A -- REPLACE ECM Removal
8. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
(a) Disconnect the camshaft position sensor for exhaust camshaft connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE ECM Removal