Transmission

Operation number: 43710-2

Transmission

Removal

Note! Removal steps in this procedure may contain installation details.

Remove Accessory Drive Component Bracket Refer to: Accessory Drive Component Bracket, B6324S5, B6324S4 Service and Repair

Remove the following items:
- Engine support insulator left Refer to: Engine Pad Left, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Engine Pad Left, Replacing
- Front subframe Refer to: Front subframe, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Service and Repair
- Driveshaft left Refer to: Driveshaft left, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Front Driveshaft, Left
- Drive shaft right Refer to: Drive shaft right, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Front Driveshaft, Right
- Engine Rear Lower Support Insulator LH Refer to: Engine Rear Lower Support Insulator LH, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S4, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC Engine Rear Lower Support Insulator LH

Torque: M6, 10 Nm

Remove the following items:
1. Torque: M10, 50 Nm

2. Torque: M8, 24 Nm

Warning! Be prepared to collect escaping fluid.

Caution! Make sure that all openings are sealed.

Remove the following items:
1. Torque: M8, 24 Nm

2. Torque: M10, 50 Nm

3. Torque: M6, 10 Nm

Remove the following items:
- starter motor Refer to: Starter motor, B6304T4, B6324S5, B6324S4 Service and Repair
- Crankshaft front seal Refer to: Crankshaft front seal, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Service and Repair

999 7257 Wrench 999 7257 Wrench
Torque: Torque converter to flexplate (screw), 60 Nm

998 5972 JACK 998 5972 JACK 999 5972 FIXTURE 999 5972 FIXTURE 999 5463 FIXTURE 999 5463 FIXTURE 999 7351 Fixture 999 7351 Fixture

999 5682 Tensioner band 999 5682 Tensioner band

Torque: M10, 50 Nm

Note! This step is only necessary when installing a new component.

Torque: M12, 80 Nm

Note! This step is only necessary when installing a new component.

Torque: M8, 24 Nm

Installation

Perform transaxle, preparations before installing

To install, reverse the removal procedure.

Carry out: gearbox oil level - check Refer to: Transmission oil level - checking, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Transmission Oil Level - Checking

Note! This step is only necessary when installing a new component.

Order and download software Programming and Relearning