Operation CHARM: Car repair manuals for everyone.
Home >> Audi >> 2011 >> TT Quattro Roadster (8J9) L4-2.0L Turbo (CETA) >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Testing and Inspection >> Scan Tool Testing and Procedures >> Diagnostic Modes 01 - 09 >> Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions

Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions






Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.

The min & max values for each individual test in Mode 06 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:






Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.

• Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements

• Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.

• No DTCs stored in the DTC memory.

• Coolant temperature at least 80° C.

Work procedure

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select Mode 6: Check test the results of components that are not continuously monitored.

Select the desired Test-ID.

The current minimum and maximum values will be displayed on the scan tool screen.

The following table is a numerical list of all"Test-IDs" or "Hex-IDs" that may be selected.






Monitor-ID $01(01) : Oxygen Sensor Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 01 ".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $02(02) : Oxygen Sensor Monitor Bank 1- Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 02".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.











- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $03(03): Oxygen Sensor Monitor Bank 1- Sensor 3

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 03".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

Monitor-ID $21(33): Catalytic Converter Monitoring

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 21".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

Monitor-ID $35(53) : Cam Shaft Adjustment

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 35".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

"Monitor-ID $3A(58) : Fuel Tank EVAP System Integrity/Leak Test (0.90)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3A ".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $3B(59) : Fuel Tank EVAP System Integrity/Leak Test (0.40/1.0mm)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3B".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $3C(60) : Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5mm)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3C".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $3D(61) : Tank vent valve - function check

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3D".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $41(65) : Oxygen Sensor Heater Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 41".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $42(66): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 42".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $43(67): Oxygen Sensor Heater Monitor Bank 1 - Sensor 3

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 43".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $71(113): Secondary air system (only SULEV)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 71".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $A2(162) : Mis-Fire Cylinder 1 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A2".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $A3(163): Mis-Fire Cylinder 2 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6 Check test the results of components that are not continuously monitored".

Select "Monitor-ID A3:".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $A4(164): Mis-Fire Cylinder 3 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A4".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

Monitor-ID $A5(165): Mis-Fire Cylinder 4 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A5".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.






- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.

- Switch the ignition off.

pro multis · About Operation CHARM