Engine Torque Specification
M52 Engine 2.5L/2.8LEngine Block
2AZ Main bearing screws
M10
With aluminum engine block
Jointing torque 20 Nm
Torque Angle 70°
Note: Replace, wash and oil screws.
With cast iron engine block
M10
Jointing torque 20 Nm
Torque Angle 50°
Note: Replace, wash and oil screws.
Cylinder Head With Cover
6AZ Cylinder head bolts
With aluminum engine block
Jointing torque 40 Nm
Torque angle 90°
Torque Angle 90°
Note: Replace, wash and oil screws.
Note: Replace, wash and oil screws.
Note: Specifications for M8 and M10 are identical.
11AZ Cylinder head cover
M6 10 Nm
M7 15 Nm
13AZ Timing case to cylinder head
M7 15 Nm
M8 20 Nm
Oil Pan
1AZ Oil drain plug
M12 x 1.5 25 Nm
M18 x 1.5 30 Nm
M22 x 1.5 60 Nm
2AZ Oil pan on engine block
M6 8.8 10 Nm
M6 10.9 12 Nm
M8 8.8 10 Nm
Oil sump, lower sections to upper section
M6 8.8 10 Nm
M8 8.8 22 Nm
Oil sump bottom section to top section with microencapsulated screws
M6 10.9 12 Nm
Note: Replace screws.
Case Cover
1AZ Timing case and timing case cover top and bottom
M6 10 Nm
M7 15 Nm
M8 22 Nm
M10 47 Nm
2AZ End cover, Front/rear, to crankcase
M6 10 Nm
M8 22 Nm
4AZ Struts/bracing shell
M10 43 Nm
M8 22 Nm
5AZ Drain plug for coolant in engine block
M14 x 1.5 25 Nm
6AZ Main oil gallery seal
16 x 1.5 34 Nm
M18 x 1.5 40 Nm
7AZ Oil spray nozzle on engine block
M6 10 Nm
Note:Oil spray nozzle to engine block (banjo bolt)
M73 M8 x 1 12 Nm
Crankshaft and bearings
1AZ Increment wheel on crankshaft
M5 10.9 13 Nm
M5 8.8 5.5 Nm
Note: Replace screws.
Flywheel
1AZ Flywheel to crankshaft
Manual transmission
Flywheel to crankshaft 105 Nm
Note: Replace Screws.
Automatic transmission
Flywheel to crankshaft 120 Nm
Note: Replace Screws.
Vibration Damper
2AZ Vibration damper / hub to crankshaft
M18 x 1.5 410 Nm
Note: Replace Screws
3AZ Belt Pulley / vibration damper to hub
M8 22 Nm
Connecting Rods and Bearings
1AZ Connecting Rod bolts
Application torque 5 Nm
Jointing torque 20 Nm
Torque angle 70°
Note: Replace, wash and oil screws.
Crankshaft
1AZ Camshaft bearing cap
M6 10 Nm
M7 14 Nm
M8 20 Nm
3AZ Sprocket to camshaft flange
M6 10 Nm
M7 15 Nm
M7
Application torque 5 Nm
Jointing torque 20 Nm
5AZ Toothed shaft to inlet camshaft
M14 x 1.5
Jointing torque 40 Nm
Torque angle 60°
8AZ Cylinder for chain tensioner plunger
M26 x 1.5 70 Nm
11AZ Screw in pin on camshaft
M7 20 Nm
Nut on screw in pin
M6 10 Nm
Variable Camshaft Control
1AZ 4/2-way valve/solenoid valve to VANOS housing 30 Nm
2AZ Banjo bolt to VANOS adjustment unit
M14 x 1.5 32 Nm
3AZ Screw plug to VANOS adjustment unit
M22 x 1.5 50 Nm
5AZ Hydraulic line for VANOS to oil filter equipment carrier 32 Nm
Oil Pump With Strainer and Drive
2AZ Oil pump to crankcase
M8 23 Nm
3AZ Oil pump cover
M6 10 Nm
4AZ Sprocket to oil pump
M6 10 Nm
M10 x 1 25 Nm
M10 45 Nm
Oil Filter and Pipes
1AZ Oil filter (one way cartridge) (Tighten to specifications on spin on oil filter)
2AZ Full flow oil filter (cover)
M8 22 Nm
M10 33 Nm
M12 33 Nm
Screwed-on cover 25 Nm
3AZ Oil filter housing and lines on crankcase
M8 22 Nm
M20 x 1.5 40 Nm
6AZ Oil line to bearing points and camshaft lubricant
M6 10 Nm
7AZ Oil line for camshaft lubricant on cylinder head
Banjo bolt M8 x 1 10 Nm
M5 5 Nm
8AZ Oil cooler oil pipes to oil filter housing
M8 22 Nm
9AZ Oil pipes to turbo charger
M8 22 Nm
10AZ Oil lines from turbocharger to engine block
Hollow bolt M16 x 1.5 40 Nm
11AZ Oil supply pipe to turbocharger
Hollow bolt 25 Nm
Coupling nut 30 Nm
Water Pump and Drive
1AZ Water pump to crankcase
M6 10 Nm
M7 15 Nm
M8 22 Nm
Fan
1AZ Fan clutch on water pump
Coupling nut
Left handed thread 40 Nm
Thermostat and Connections
1AZ Thermostat housing
M6 10 Nm
2AZ Bleeder screw
M8 8 Nm
Intake Manifold
1AZ Intake manifold on cylinder head
M8 22 Nm
M7 15 Nm
M6 10 Nm
Exhaust Manifold
1AZ Exhaust manifold to cylinder head
Coat screw connections with Molykote HSC past
M6 10 Nm
Note: Replace Nuts.
M7 20 Nm
Note: Replace Nuts.
M8 23 Nm
Note: Replace Nuts.
Emissions-Control, Lambda Oxygen Sensor
1AZ Oxygen control sensor, oxygen monitor sensor
M18 x 1.5 50 Nm