4L80-E / 4L85-E Automatic Transmission

DTC P0752

Circuit Description with 4L80-E / 4L85-E Automatic Transmission
The 1-2 shift solenoid (SS) valve controls the fluid flow on the 1-2 and the 3-4 shift valves. The 1-2 SS valve is a normally-open exhaust valve that is used with the 2-3 SS in order to allow four different shifting combinations. When the powertrain control module (PCM) detects a 1-1-4-4 gear ratio, then DTC P0752 sets. DTC P0752 is a type C DTC. For California emissions vehicles and vehicles under 8,600 GVW, DTC P0752 is a type B DTC.

Conditions for Running the DTC
* No MAP sensor DTCs P0106, P0107, or P0108.
* No Transmission Component Slipping DTC P0894.
* No TP sensor DTCs P0121, P0122, or P0123.
* No ISS sensor DTCs P0716 or P0717.
* No VSS DTCs P0502 or P0503.
* No MAF DTCs P0101, P0102 or P0103.
* No TFP manual valve position switch DTC P1810.
* Not in 4WD Low.
* No TCC PWM solenoid valve DTC P1860.
* No TCC Stuck ON DTC P0742.
* The system voltage is 10 - 18 volts.
* Transmission ISS is greater than 7 RPM.
* The transmission OSS is greater than 7 RPM.
* No shift solenoid electrical DTCs P0753 or P0758.
* The throttle angle sensor is greater than 10 percent.
* The engine torque must be between 108 Nm (80 ft. lbs.) and:
- 6.0L: 576 Nm (425 ft. lbs.)
- 8.1L: 881 Nm (650 ft. lbs.)
* No TFP manual valve position switch change within 6 seconds.
* The TFP manual valve position switch indicates D4.
* The transmission fluid temperature (TFT) is greater than 20°C (68°F).

Conditions for Setting the DTC
* The commanded gear equals 2nd and the ratio equals 1st for greater than 2.25 seconds.
* All conditions are met for 5 occurrences.

Action Taken When the DTC Sets
* For California emission equipped vehicles, the PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. For Federal emission equipped vehicles, the MIL is not illuminated.
* The PCM commands maximum line pressure.
* The PCM inhibits 3-2 downshifts above 40 km/h (25 mph)
* The PCM freezes shift adapts.
* The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame, California only, and Failure Records, California and Federal.
* The PCM stores the DTC P0752 in PCM history during the second consecutive trip, California, or the first trip, Federal, in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC
* For California emissions, the PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
* A scan tool can clear the MIL/DTC.
* For California emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring.
* For Federal emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring.
* The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids
* Verify that the transmission meets the specifications in the Shift Speed table.
* Other internal transmission failures can cause more than one shift to occur.
* DTC P0752 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine.

Test Description
The number below refers to the step number on the diagnostic table.
2. This step tests that the PCM commanded all shifts, that all shift solenoid valves responded correctly. hut that all the shifts did not occur.

Steps 1 - 2:

Steps 3 - 5:

DTC P0752