Brake Warning Indicator Malfunction
Brake Warning Indicator Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The instrument panel cluster (IPC) sees the brake fluid level switch input opens and illuminates the Red Brake Warning indicator. The body control module (BCM) sees the park brake switch input grounded, it sends a serial data message to the IPC requesting illumination of the Red Brake Warning indicator.
Reference Information
Schematic Reference
Hydraulic Brake Schematics [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Brake Warning System Description and Operation Brake Warning System
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Verify the park brake is released and the brake fluid is at or above the proper level.
• If low, refer to Brake Fluid Loss Brake Fluid Loss.
2. Command the IPC display test with a scan tool, the warning indicator should turn ON.
• If the red brake warning indicator does not illuminate, replace the IPC.
3. Ignition ON, observe the scan tool BCM Park Brake Switch parameter while applying and releasing the park brake. The parameter should cycle between Active and Inactive.
• If the parameter does not cycle between the specified values, refer to Park Brake Switch Malfunction.
4. Observe the scan tool IPC Brake Fluid Level Switch parameter. The reading should be OFF.
• If not the specified value, refer to Brake Fluid Level Switch Malfunction.
Circuit/System Testing
Park Brake Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the park brake switch.
2. Ignition ON, verify the scan tool BCM Park Brake Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal A for a short to ground. If the circuit tests normal, replace the BCM.
3. Install a 3A fused jumper wire between the signal circuit terminal A and ground. Verify the scan tool BCM Park Brake Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance.
4. If all circuits test normal, test or replace the park brake switch.
Brake Fluid Level Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the brake fluid level switch.
2. Test for less than 5 ohms between the ground circuit terminal 2 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, test for 4.8 - 5.2 volts between the 5 volt reference circuit terminal 1 and ground.
• If less than the specified range, test the 5 volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the IPC.
• If greater than the specified range, test the 5 volt reference circuit for a short to voltage. If the circuit tests normal, replace the IPC.
4. If all circuits test normal, test or replace the brake fluid level switch.
Component Testing
Park Brake Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the park brake switch.
2. Test for infinite resistance between the signal terminal A and ground with the park brake released.
• If less than the specified value, replace the park brake switch.
3. Test for less than 1 ohm between the signal terminal A and ground with the park brake applied.
• If greater than the specified range, replace the park brake switch.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Brake Fluid Level Indicator Switch Replacement Service and Repair
* Parking Brake Indicator Switch Replacement (9C3) Parking Brake Indicator Switch Replacement (9C3)Parking Brake Indicator Switch Replacement (9C1) Parking Brake Indicator Switch Replacement (9C1)
* Control Module References Control Module References for BCM and IPC replacement, setup, and programming