B.Instrument Panel Harnesses Pn 4362289, All Models

FIGURE 2A - TERMINAL END OF BULKHEAD CONNECTOR (INSTRUMENT PANEL SIDE):

1. Remove instrument panel left lower trim panel.

2. Insert two bare terminals from instrument panel overlay harness, PN 4362289, into the instrument panel side of the bulkhead connector (Figure 2-A).

a. Gray with black tracer wire into cavity #14.
b. Dark green wire into cavity #13.

INSTRUMENT PANEL WIRING:

3. Secure bare eyelet ground terminal (white with black tracer wire) from instrument panel overlay harness, PN 4362289, with screw, PN 9414722, to the back of the brake bracket (Figure 2-B).

NOTE: CERTAIN VEHICLES ARE ALREADY EQUIPPED WITH THE
GROUND SCREW. IF SO, DISCARD THE SUPPLIED SCREW.

FIGURE 2C - INSTRUMENT PANEL WIRING:

FIGURE 2D - INSTRUMENT PANEL WIRING:

4. Disconnect the arced grey 7-way ignition switch connectors and remove the orange wire from the instrument panel side (Figure 2-C).

Install the extracted terminal (orange wire) into the natural colored 1-way connector supplied with instrument panel overlay harness, PN 4362289.

Install the bare terminal (orange wire) from the instrument panel overlay harness, PN 4362289, into the vacated cavity in the ignition switch connector. Reconnect the natural colored 1-way connectors supplied with the instrument panel overlay harness, PN 4362289, and reconnect the ignition switch connectors (Figure 2-C and 2-D).

FIGURE 2E - TYPICAL CONTROL MODULE MOUNTING:

5. Connect the control (auto shut-down) module, PN 5226640, to the natural colored 8-way connector from instrument panel overlay harness, PN 4362289. Secure the module onto the main instrument panel wiring harness with a tie wrap, PN 6015756, close to the bulkhead connector (Figure 2-E).

INSTRUMENT PANEL WIRING:

FIGURE 2D - INSTRUMENT PANEL WIRING:

FIGURE 2F - INSTRUMENT PANEL WIRING:

6. Route the orange colored 1-way connector from the instrument panel overlay harness, PN 4362289, to the back of the brake bracket for mating in a later step (Figures 2-B, 2-D, and 2-F).

Secure instrument panel overlay harness, PN 4362289, using tie wrap, PN 6015756, to keep it clear of any possible interferences.
Only one of the following installation procedures (Step 7) will be used. Take notice of which one applies to the vehicle being repaired.

7. Without Auxiliary Air Conditioning and/or Heater - Jumper Harness PN 4362291

a. Remove instrument panel hood and bezel assembly and remove radio.

FIGURE 2D - INSTRUMENT PANEL WIRING:

b. Route instrument panel jumper harness, PN 4362291, from the back of the brake bracket to the existing 3-way red molded connector. Secure by using existing wiring clips (Figure 2-D).
c. Insert the bare bullet terminal (black with white tracer wire) from instrument panel jumper harness, PN 4362291, into the existing 3-way red molded connector from the main instrument panel wiring harness (Figure 2-D).

d. Mate the orange colored 1-way connector from instrument panel jumper harness, PN 4362291, to the orange colored 1-way connector from the instrument panel overlay harness, PN 4362289 (Figure 2-D).

e. Reinstall instrument panel hood and bezel assembly and install radio.

FIGURE 2F - INSTRUMENT PANEL WIRING:

7. With Auxiliary Air Conditioning and/or Heater and Power Windows - Jumper Harness PN 4362292

a. Disconnect from each other, the two existing brown colored 1-way connectors located near the left instrument panel vent (Figure 2-F).

Reconnect these two brown colored 1-way connectors to the two brown colored 1-way connectors from instrument panel jumper harness, PN 4362292 (Figure 2-F).

b. Mate the orange colored 1-way connector from the instrument panel jumper harness, PN 4362292, to the orange colored 1-way connector from instrument panel overlay harness, PN 4362289 (Figure 2-F).

INSTRUMENT PANEL WIRING:

7. With Auxiliary Air Conditioning and/or Heater Without Power Windows - Relay Harness PN 4362290

a. Remove instrument panel hood and bezel assembly. Remove radio.

b. Install the ignition switch protection relay, PN 4162597, to the back of the brake bracket (mounting location shown in Figure 2-B) and attach instrument panel relay harness, PN 4362290, to relay.

c. Secure bare eyelet ground terminal (white wire) from instrument panel relay harness, PN 4362290, with screw, PN 9414722, to the back of the brake bracket (Figure 2-B).

FIGURE 2D - INSTRUMENT PANEL WIRING:

d. Route the dark blue wire from the instrument panel relay harness, PN 4362290 to the existing 3-way red molded connector using existing wiring clips. Insert bullet terminal (dark blue wire) into red molded connector (Figure 2-D).

INSTRUMENT PANEL WIRING:

e. Insert bare bullet terminal (red wire) from instrument panel relay harness, PN 4362290, into the existing 3-way yellow molded connector from the main instrument panel wiring harness (Figure 2-B).

FIGURE 2D - INSTRUMENT PANEL WIRING:

f. Mate the orange colored 1-way connector from instrument panel relay harness, PN 4362290, to the colored 1-way connector from the instrument panel overlay harness, PN 4362289 (Figure 2-D).
g. Install the instrument panel left lower trim panel, instrument panel hood, bezel assembly and radio.