60 Percent
FRONT SEAT - 60 PERCENTSpecial Tool(s):
SPECIAL TOOL(S)
REMOVAL
WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe pretensioner electrical connectors. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.
The front impact severity sensor is located at the bottom of the hood latch support bracket.
The first row side impact sensors (if equipped) are located in the first row doors, behind the door trim panel.
The second row side impact sensors (if equipped) are located at or near the base of the C-pillars.
To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
NOTE: Before disconnecting the battery in vehicles with power seats, adjust the seat position to allow for access to the necessary components.
Disconnect the battery ground cable and wait at least one minute.
2. WARNING: To reduce the risk of serious personal injury, read and follow all warnings, cautions, notes, and instructions in the supplemental restraint system (SRS) deactivation/reactivation procedure.
Deactivate the supplemental restraint system (SRS).
3. Remove the front seat rear floor bolt covers.
4. Remove the 60 percent front seat rear bolts.
1 Disconnect the usage detection electrical connector.
2 Remove the center seat belt anchor bolt.
3 Remove the two seat-to-floor bolts.
5. Move the 60 percent seat to its rearmost position.
6. Remove the two front seat-to-floor bolts (one shown).
7. NOTE: Removing the 60 percent front seat requires more than one technician.
Remove the 60 percent seat from the vehicle.
INSTALLATION
WARNING: To reduce the risk of serious personal injury, read and follow all warnings, cautions, and notes at the beginning of the removal procedure.
1. NOTE: Installing the 60 percent front seat requires more than one technician.
Install the 60 percent seat in the vehicle.
2. Install the front seat-to-floor bolts (one shown).
- Make sure the safety belt webbing is not twisted prior to installation.
3. Move the 60 percent seat to its most forward position.
4. NOTE: Make sure the LH rear seat belt anchor is located before securing the seat.
Install the front seat rear bolts.
1 Connect the usage detection electrical connector.
2 Install the two seat-to-floor bolts.
3 Install the center seat belt anchor bolt.
5. NOTE: Make sure the negative battery cable is still disconnected before proceeding with the reactivation portion of this procedure.
Remove the restraint system diagnostic tool from the passenger seat safety belt buckle pretensioner floor electrical connector.
6. Connect the passenger seat safety belt buckle pretensioner electrical connector.
1 Connect the passenger seat safety belt buckle pretensioner electrical connector.
2 Slide and engage the passenger seat safety belt buckle pretensioner electrical connector locking clip.
7. Connect the battery ground cable.
8. With the restraint system diagnostic tools still installed at the remaining deployable devices, prove out the supplemental restraint system (SRS).
9. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.
The front impact severity sensor is located at the bottom of the hood latch support bracket.
The first row side impact sensors (if equipped) are located in the first row doors, behind the door trim panel.
The second row side impact sensors (if equipped) are located at or near the base of the C-pillars.
To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
Disconnect the battery ground cable and wait at least one minute.
10. WARNING: To reduce the risk of serious personal injury, read and follow all warnings, cautions, notes and instructions in the supplemental restraint system (SRS) deactivation/reactivation procedure.
Reactivate the supplemental restraint system (SRS).
11. WARNING: The restraint system diagnostic tool is for restraint system service only. Remove from the vehicle prior to road use. Failure to remove could result in injury and possible violation of vehicle safety standards.
With all the restraint system diagnostic tools removed, prove out the supplemental restraint system (SRS).
12. Check the active restraint system for correct operation.