Torque Specifications

Description Torque
Air Cleaner Outlet Tube Clamp 1.7-3.3 Nm (15-29 Inch Lbs.)
Main Bearing Cap Adjusting Screws please see note a
Main Bearing Cap Adjusting Screw Bolts please see note b
Camshaft Sprocket Bolt 110-130 Nm (81-95 Ft. Lbs.)
Connecting Rod Bolt please see note c
Engine Front Cover Bolt 20-30 Nm (15-22 Ft. Lbs.
Drive Belt Tensioner Bolts 20-30 Nm (15-22 Ft. Lbs.)
Drive Belt Idler Pulley Bolt 20-30 Nm (15-22 Ft. Lbs.)
Engine Lifting Eyes 40-50 Nm (30-37 Ft. Lbs.
Cylinder Head Bolt please see note d
Pulley to Crankshaft Bolt 155-165 Nm (114-121 Ft. Lbs.)
EGR Valve to Upper Intake Manifold 20-30 Nm (15-22 Ft. Lbs.)
EGR Vacuum Regulator Bolts 5-7 Nm (45-60 Inch Lbs.)
Lower Intake Manifold-to-Cylinder Head Bolt please see notes e & f
Main Bearing Cap Bolt please see notes g & h
Low Oil Level Sensor 27-41 Nm (20-30 Ft. Lbs.)
Oil Filter Adapter Bolt 20-30 Nm (15-22 Ft. Lbs.)
Engine Oil Cooler to Oil Filter Adapter 80-100 Nm (59-74 Ft. Lbs.)
Oil Bypass Filter to Engine Oil Cooler please see note i
Oil Pump Screen Cover and Tube-to-Oil Pump Bolt 8-12 Nm (71-106 Inch Lbs.)
Oil Pan Drain Plug 11-16 Nm (8-12 Ft. Lbs.)
Oil Pan-to-Cylinder Block Bolt 20-30 Nm (15-22 Ft. Lbs.)
Oil Pan-to-Engine Front Cover Bolts 20-30 Nm (15-22 Ft. Lbs.)
Oil Pump-to-Cylinder Block Bolt 8-12 Nm (71-106 Inch Lbs.)
Oil Pump Screen Cover and Tube-to-Main Bearing Cap Stud Spacer Bolt 20-30 Nm (15-22 Ft. Lbs.)
Water Pump Pulley Bolts 20-30 Nm (15-22 Ft. Lbs.)
Generator to Cylinder Block 20-30 Nm (15-22 Ft. Lbs.)
Valve Cover Bolts/Stud Bolt 8-12 Nm (71-106 Inch Lbs.)
Water Pump-to-Cylinder Block Bolt 20-30 Nm (15-22 Ft. Lbs.)
Flywheel Bolts 73-87 Nm (54-64 Ft. Lbs.
EGR Tube Connector 45-65 Nm (33-48 Ft. Lbs.
EGR Valve to Exhaust Manifold Tube Nuts 40-45 Nm (30-33 Ft. Lbs.)
Exhaust Manifold Nuts 18-22 Nm (13-16 Ft. Lbs.
Secondary Air Injection Manifold Tube Nuts to Exhaust Manifold 38-42 Nm (28-31 Ft. Lbs.)
Engine Insulators 20-30 Nm (15-22 Ft. Lbs.)
Front Engine Support Insulator Through Bolts 20-30 Nm (15-22 Ft. Lbs.)
Power Steering Pump to Engine 20-30 Nm (15-22 Ft. Lbs.)
Power Steering Pump Reservoir Retaining Bolts 8-12 Nm (71-106 Inch Lbs.)
Fuel Injection Supply Manifold Retaining Bolts 8-12 Nm (71-106 Inch Lbs.)
Rear Oil Seal Retainer Bolts 8-12 Nm (71-106 Inch Lbs.)
Outlet Heater Water Hose to LH Cylinder Head Upper Bolt 20-30 Nm (15-22 Ft. Lbs.)
Outlet Heater Water Hose to LH Cylinder Head Lower Bolt 8-12 Nm (71-106 Inch Lbs.)
Camshaft Cap to Cylinder Head 8-12 Nm (71-106 Inch Lbs.)
Engine to Transmission Retaining Bolts 40-60 Nm (30-44 Ft. Lbs.)
Inlet Heater Water Hose to RH Cylinder Head Upper Bolt 20-30 Nm (15-22 Ft. Lbs.)
Inlet Heater Water Hose to RH Cylinder Head Lower Bolts 8-12 Nm (71-106 Inch Lbs.)
Front Suspension Upper Arm-to-Front Wheel Hub and Spindle 68-92 Nm (50-68 Ft. Lbs.)
Front Suspension Lower Arms to Strut Bolt 160-220 Nm (118-162 Ft. Lbs.)
Intake Manifold to Lower Intake Manifold Bolts 8-10 Nm (71-89 Inch Lbs.)
Upper Intake Manifold to Intake Manifold Bolts 8-12 Nm (71-106 Inch Lbs.)
Water Bypass Tube Nuts 8-12 Nm (71-106 Inch Lbs.)
Torque Converter Retaining Nuts 30-35 Nm (22-25 Ft. Lbs.)
Timing Chain Tensioner Bolts 20-30 Nm (15-22 Ft. Lbs.)
A/C Compressor Retaining Bolts 20-30 Nm (15-22 Ft. Lbs.)
CKP and CMP Sensor Retaining Bolts 8-12 Nm (71-106 Inch Lbs.)
ECT Sensor 16-24 Nm (12-17 Ft. Lbs.)
Idle Air Control Valve Bolts 8-12 Nm (71-106 Inch Lbs.)
Coolant Temperature Switch 16-22 Nm (12-17 Ft. Lbs.)
Throttle Body Bolts (f) 8-12 Nm (71-106 Inch Lbs.)
Spark Plugs 9-20 Nm (7-15 Ft. Lbs.)
Ignition Wire Cover Retainers 5-7 Nm (45-60 Inch Lbs.)
Fuel Injection Supply Manifold Retaining Bolts 8-12 Nm (71-106 Inch Lbs.)
Generator Mounting Bracket Retainers 8-12 Nm (71-106 Inch Lbs.)
Oil Level Indicator Tube Retainer 8-12 Nm (71-106 Inch Lbs.)
Front Sub-Frame to Body Bolts 95-130 Nm (70-96 Ft. Lbs.)
Rear Engine Support Insulator-to-Support 20-30 Nm (15-22 Ft. Lbs.)
Primary Timing Chain Guide-to-Engine Bolts 8-12 Nm (71-106 Inch Lbs.)
Timing Chain Tensioner Arm Bolts 10-15 Nm (7-11 Ft. Lbs.)
Oil Pressure Sensor 12-16 Nm (9-12 Ft. Lbs.)
Accelerator Cable Bracket 8-12 Nm (71-106 Inch Lbs.)
Ignition Coil Brackets-to-Engine Front Cover 20-30 Nm (15-22 Ft. Lbs.)
Rear Axle Assembly-to-Rear Sub-Frame Nuts 98-120 Nm (72-89 Ft. Lbs.)
Rear Axle Differential Nuts 102-127 Nm (75-89 Ft. Lbs.)
Driveshaft Centering Socket Yoke-to-Rear Axle Universal Joint Flange Bolts 95-130 Nm (70-96 Ft. Lbs.)

a Tighten in 2 steps:
First step, 5 Nm (44 Lb-In)
Second step, 10 Nm (89 Lb-In)

b Tighten in 2 Steps:
First step, 10 Nm (7 Lb-Ft)
Second step, 19-23 Nm (14-17 Lb-Ft)

c Tighten in 2 steps:
First step, 25-35 Nm (18-25 Lb-Ft)
Second step, rotate 85-95 degrees

d Tighten in 3 steps:
First step, 37-43 Nm (27-32 Lb-Ft)
Second step, rotate 85-95 degrees
Third step, rotate 85-95 degrees

e Tighten 1-20 in numerical sequence to 20-30 Nm (15-22 Lb-Ft)

f Rotate in numerical sequence 85-95 degrees.

g Tighten fasteners in sequence as shown:
1. Fasteners 1 through 8 to 8-12 Nm (71-106 Lb-In)
2. Fasteners 10 through 18 to 8-12 Nm (71-106 Lb-In)
3. Seat thrust washer
4. Fasteners 9, 10, 19 and 20 in order to 8-12 Nm (71-106 Lb-In)
5. Fasteners 1 through 10 to 22-28 Nm (16-21 Lb-Ft)
6. Fasteners 11 through 20 to 37-43 Nm (27-32 Lb-Ft)

h Rotate in numerical sequence 85-95 degrees.

i 3/4 turn after gasket contacts sealing surface.