Driver Information/Message Center
MESSAGE CENTER
The message center system consists of:
1. Message Center Indicator.
2. Message Center Switch Module.
Message Center Switch Module
The message center switch module, has seven switches and is located below the message center indicator in the center console. The message center switches are:
- English/Metric mode.
- Fuel Computer.
- Range.
- Status.
- Economy.
- System Check and Warnings.
- Warning Chimes.
Display Dimming
The dimming of the indicator display is controlled by the pulse width dimmer module. The voltage on Pin 2 controls the brightness of the message center display. When the exterior lamps are OFF, this voltage will be zero volts and the message center display will be at maximum brightness. When the exterior lamps are ON, this voltage will be controlled by the pulse width dimmer module and will be between 2.5 volts and battery voltage. The message center display will be brighter as this voltage approaches battery voltage. If there is a warning on the message center display, the display will not dim to its lowest level.
When the headlamps or parking lamps are OFF, the display of the message center indicator will be maximum brightness and the labels for the center five switches of the message center switch module will not be illuminated.
When the headlamps or parking lamps are ON, the brightness of the display of the message center indicator and the labels for the center five switches of the message center switch module will be controlled by the pulse width dimmer module.
English/Metric Mode
The English/Metric switch controls the display mode for both the message center indicator and the electronic automatic temperature control. A press of the English/Metric switch will change both displays between English mode and Metric mode.
Fuel Computer
The fuel computer of the message center indicator uses information from other modules and sensors to perform calculations.
Range
The Range feature has two displays: 1) the distance that can be traveled before refueling, and 2) the distance that was traveled since the last trip odometer reset. The range switch will change the message center indicator between the two displays.
The Range (Distance to Empty) feature is calculated using the fuel flow signal from the Powertrain Control Module (PCM), the speed signal from the Vehicle Speed Sensor (VSS) and the fuel level signal from the fuel level sensor, which is a part of the fuel pump.
The fuel flow and speed signals are used to calculate a Running Average Fuel Economy (RAFE), which is multiplied by the fuel remaining to give the range.
RAFE is not the same number as the Average Fuel Economy displayed by the message center indicator.
RAFE is based on the past driving history and can only be reset by disconnecting the battery.
When the range decreases to 80 km (50 miles) to empty, the message center will display the LOW FUEL LEVEL warning.
With a fuel tank full of fuel (160 ohm signal from fuel sender) and after a battery disconnect, the Range should be approximately 400 miles to empty.
The Range (Trip Odometer) feature is calculated using the speed signal from the vehicle speed sensor. It can be reset to zero by pressing the reset switch while the trip odometer is displayed on the message center.
Status
The Status feature has two displays, fuel-to-empty and fuel-used. The Status switch will change the message center indicator between the two displays.
- The fuel-to-empty calculation is achieved using the fuel level signal from the fuel level sensor.
- The fuel-used feature is calculated using the fuel flow signal from the powertrain control module and can be reset to zero by pressing the RESET switch while the fuel-used feature is displayed on the message center.
Economy
The Economy feature has two displays: Average and Instant. Depressing the Economy switch changes the message center indicator between both displays.
- The economy calculations are achieved using the fuel flow signal from the powertrain control module and the speed signal from the vehicle speed sensor.
- The average fuel economy feature can be reset by pressing the RESET switch while the average fuel economy feature is displayed on the message center indicator.
System Check and Warnings
The SYSTEM CHECK feature cycles the message center indicator through a status of each system being monitored.
- For each of the monitored systems, the message center indicator will indicate either an OK message or a warning message for two seconds.
- At normal conclusion of the system check sequence, the message center indicator will display all active warnings or the last feature displayed before entering the SYSTEMS CHECK mode.
- System warnings alert the driver to possible concerns or malfunctions in the vehicle's operating systems.
- There are 12 warning messages which can be displayed for two seconds by the message center indicator to show the status of the monitored systems.
- When a warning occurs, the warning message is displayed and a one-second tone sounds. The warning message will appear at a brighter level if the message center indicator is dimmed.
- In the event of a multiple warning situation, the message center indicator will cycle the display to show all warnings by displaying each warning message for four seconds.
- To display the operator selectable features of the message center indicator while a warning is displayed, the warning message may be removed from the message center indicator display by pressing the RESET switch. The message center indicator will display the last selected feature if there are no more warning messages.
- This allows operation of all functions of the message center indicator after pressing the RESET switch and clearing the warning message.
Warning messages which have been reset will either reappear on the display in 10 minutes from the reset or will not reappear until an ignition switch OFF-RUN cycle.
If warning messages reappear it is a reminder that these warning conditions still exist. Warnings may be repeatedly reset. All warning messages will reappear for four seconds after an entire SYSTEM CHECK sequence has been completed.
Air Suspension Switch Warning (AIR RIDE SWITCH OFF)
This warning message is displayed when the rear suspension leveler compressor switch, located in the luggage compartment on the LH side, is OFF.
- When the rear suspension leveler compressor switch is ON, the input at C2008-12 to the message center indicator is pulled to 5 volts.
- When the rear suspension leveler compressor switch is OFF, the input at C2008-12 to the message center indicator is an open circuit and the warning will be displayed.
Air Suspension System Warning (CHECK AIR RIDE SYSTEM)
This warning message is displayed when an air suspension system diagnostic trouble code has been detected by the air suspension/EVO control module.
Charging System Warning (CHECK CHARGING SYSTEM)
This warning message is displayed when the electrical system is not maintaining a proper voltage at the message center indicator. There will be a few seconds delay before the warning is displayed or removed.
Engine Coolant Temperature Warning (CHECK ENGINE TEMP)
This warning message is displayed when the engine coolant is overheating.
The message center indicator senses the voltage level on Circuit 39 (R/W) (C2008-8 to the message center indicator).
If that voltage is greater than approximately 2.7 volts at a battery voltage of 13.5 volts there will be no warning. If it is less than approximately 2.7 volts, at a battery voltage of 13.5 volts then the warning will be displayed.
The message center indicator filters this input; therefore there will be a few seconds delay before the warning is displayed or removed.
Fuel Level Warning (LOW FUEL LEVEL)
This warning message is displayed when there is approximately 80 km (50 miles) left before the vehicle runs out of fuel.
Lamp-Out Warning (CHECK HEADLAMPS, BRAKELAMPS, AND TAIL LAMPS)
NOTE: If the message center module detects an intermittent lamp-out signal from the lamp-outage module, it will latch in the lamp-out signal until the next ignition-key cycle.
These warning messages are displayed when one of the following lamps is turned on and at least one of them is burned out:
- Brakelamp.
- Rear parking lamp.
- Low beam headlamp (a high beam headlamp burnout is not monitored).
When the lamp out control module detects that its system is operating normally, and all lamps are functioning, the inputs to the message center indicator will be open circuits.
When the lamp out control module detects a burned-out lamp in its system, it will ground the input to the message center indicator and the warning will be displayed.
At Key ON, there is a one-second prove-out pulse are pulled to ground by the lamp out indicator warning control module If the message center indicator does not receive the prove-out pulse, it will display the Lamps Outage ERROR message during system check sequence.
Oil Level Warning (LOW OIL LEVEL)
This warning message is displayed when the engine oil level is low.
When the engine oil level is normal, the input to the message center indicator will be an open circuit.
When the engine oil level is low, the low oil level sensor in the combination oil temperature/low oil level sensor will close, grounding the input to the message center indicator and the warning will be displayed during the next ignition cycle of OFF to RUN. This low oil level sensor is only monitored when the ignition switch is in OFF.
There is a delay of up to 12 minutes in this monitoring in order to allow the oil to drain back into the oil pan and reach the correct level.
Oil Life Warning (CHANGE OIL SOON or OIL CHANGE REQUIRED)
If the connection to the oil temperature sensor is open circuit or shortened, the message center display will read "0, Temperature Signal Error," instead of "Percentage Oil Life Left," during system check sequence.
One of these warning messages is displayed when the engine oil life remaining is five percent or less.
- When oil life left is between five percent and zero percent, the "CHANGE OIL SOON" message will be displayed.
- When oil life left reaches zero percent, the "OIL CHANGE REQUIRED" message will be displayed.
The message center indicator will indicate the percent of oil life left during System Check. This percentage is based on the driver's driving history and the time since the last oil change. In order to ensure accurate oil life left indications, the driver should only perform the OIL CHANGE RESET procedure, as described in the Owner Guide, after an oil change.
To calculate the percentage of oil life remaining, the oil life feature uses:
- The oil temperature sensor input.
- The tachometer input from the Ignition Control Module (ICM).
- The Vehicle Speed Sensor (VSS) input.
- Clock time (maintained internally by the message center).
- The oil life will decrease from 100 percent to 0 percent in no more than 12,068 km (7,500 mi) or 6 months. It will reach zero percent sooner under different driving conditions.
- The percentage of oil life left is the second display in the system check sequence.
- When oil life left is between five percent and zero percent, the "CHANGE OIL SOON" message will be displayed.
- When oil life left reaches zero percent, the "OIL CHANGE REQUIRED" message will be displayed.
Washer Fluid Level Warning (LOW WASHER FLUID)
This warning message is displayed when there is less than one quarter of the container of washer fluid remaining.
- When the washer fluid level is normal, the windshield washer reservoir fluid level sensor will close, grounding the input at C2009-31 of the message center indicator.
- When the washer fluid level is low, the input to the message center indicator will be open and the warning will be displayed.
The message center indicator filters this input - therefore, there will be a 20-second delay before the warning is displayed or removed.
Warning Chime
A short warning chime (0.1 second) is output with every message center switch press. A longer warning chime (1.0 second) is output when a new warning first appears on the message center indicator display.
To activate the warning, pull the chime request output below one volt during the length of the tone.