Limited

DISASSEMBLY

WARNING:
^ ALWAYS WEAR SAFETY GLASSES WHEN REPAIRING AN AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) VEHICLE AND WHEN HANDLING AN AIR BAG MODULE. THIS WILL REDUCE THE RISK OF INJURY IN THE EVENT OF AN ACCIDENTAL DEPLOYMENT.
^ AFTER DEPLOYMENT, THE AIR BAG SURFACE CAN CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTERWARD.

1. Disassemble the seat.

NOTE: Be sure to read and follow all air bag warnings.







2. Disconnect the seat backrest recliner actuator.
1. Remove the screws.
2. Disconnect the seat backrest recliner actuator.
3. If equipped, disconnect the seat cushion heating element electrical connector.







4. Remove the seat cushion frame from the seat cushion foam.
1. Unhook the seat cushion trim cover J-clips.
2. Remove the seat cushion frame from the seat cushion foam.







5. Invert the seat cushion trim cover.







6. Remove and discard the hog rings.
1. Fold back the seat cushion trim cover to expose the hog rings.
2. Remove and discard the hog rings.

NOTE: The hog rings along the front of the seat are shown, the hog rings along either side are similar.







7. If equipped, and if necessary, remove the seat cushion heating element from the seat cushion foam.

CAUTION: Any time the seat cushion heating element is removed from the seat cushion foam, the foam must be replaced.







8. Disconnect the [1][2]heated seat module electrical connector.







9. Remove the [1][2]heated seat module.
1. Release the clip.
2. Remove the [1][2]heated seat module.







10. Remove the Driver Seat Module (DSM).
1. Remove the screws.
2. Disconnect the electrical connectors.
3. Remove the DSM.







11. Disconnect the lumbar support adjusting pump electrical connector.







12. Remove the power seat wiring harness.
1. Disconnect the pin-type retainers.
2. Remove the power seat wiring harness.







13. Remove the flexilator.
1. Remove the flexilator springs.
2. Remove the flexilator.







14. Remove the lumbar support adjusting pump.
1. Remove the bolt.
2. Remove the lumbar support adjusting pump.







15. Remove the seat backrest recliner roll pins and remove the seat backrest recliners.







16. Disconnect the seat backrest recliners from the seat backrest recliner actuator.
1. Disconnect the seat backrest recliner actuator cable housings from the seat backrest recliners.
2. Unhook the seat backrest recliner actuator cables from the seat backrest recliners.

ASSEMBLY







1. Connect the seat backrest recliners to the seat backrest recliner actuator.
1. Hook the seat backrest recliner actuator cables to the seat backrest recliners.
2. Connect the seat backrest recliner actuator cable housings to the seat backrest recliners.







2. Install the seat backrest recliner roll pins.







3. Install the lumbar support adjusting pump.
1. Position the lumbar support adjusting pump.
2. Install the bolt.







4. Install the flexilator.
1. Position the flexilator.
2. Install the flexilator springs.







5. Install the power seat wiring harness.
1. Position the power seat wiring harness.
2. Install the pin-type retainers.







6. Connect the lumbar support adjusting pump electrical connector.







7. Install the DSM.
1. Connect the electrical connectors.
2. Position the DSM.
3. Install the screws.







8. Install the hog rings.
1 Fold back the seat cushion trim cover to the hog ring installation position.
2 Install the hog rings.

NOTE: The hog rings along the front of the seat are shown; the hog rings along either side are similar.







9. Invert the seat cushion trim cover.







10. Install the seat cushion frame.
1. Position the seat cushion frame.
2. Hook the seat cushion trim cover J-clips.
11. If equipped, connect the seat cushion heating element electrical connector.







12. Connect the seat backrest recliner actuator.
1. Connect the seat backrest recliner actuator.
2. Install the screws.
^ Tighten until the screws are fully seated.
13. Assemble the seat.

NOTE: Be sure to read and follow all air bag warnings.