Removal and Installation

Main Control Valve Body

Special Tools:

Special Tool(s)

Removal

1. with the vehicle in NEUTRAL, position it on a hoist.

2. NOTE: If equipped, the transmission servo heat shield needs to be unclipped from the fluid pan rail and positioned out of the way for fluid pan removal.






If equipped, loosen the nut and position the heat shield out of the way.






3. Drain transmission fluid.
- Remove all the transmission fluid pan screws except for two in the front. Loosen the two front transmission fluid pan screws. Pry the rear of the transmission fluid pan down and allow fluid to drain. After fluid is drained remove the front two transmission fluid pan screws.






4. Remove the transmission fluid pan.

1. Remove the transmission fluid pan.
2. Remove and discard the transmission fluid pan gasket.






5. Remove and discard the transmission fluid filter.

1. Remove the transmission fluid filter screw.
2. Remove the transmission fluid filter.






6. Unclip main control valve body wire harness.

- Lift up on wire harness guide and protector and disengage the retaining pins from the solenoid clamps.






7. Disconnect the six solenoid electrical connectors.

1. Disconnect the SSA, SSB, SSC and SSD electrical connectors.
2. Disconnect the torque converter clutch (TCC) solenoid electrical connector.
3. Disconnect the electronic pressure control (EPC) solenoid electrical connector.






8. Remove the manual control valve detent lever spring.

1. Remove the manual control valve detent lever spring screw.
2. Remove the manual control valve detent lever spring.






9. Remove the low/reverse servo.

1. Remove the low/reverse servo cover screws.
2. Remove the low/reverse band servo cover and gasket. Discard the low/reverse servo separator plate cover gasket.






10. Remove the low/reverse band servo piston and rod.






11. CAUTION: Support the main control valve body.

Do not remove the two (gold) screws specified.






12. CAUTION: Support the main control valve body.

Remove the screws.

13. Remove the main control valve body.

Installation






1. Install the special tool into the transmission case.






2. Position the main control valve body with the two special tools as a guide.






3. NOTE: The main control valve body screws will be tightened in later steps.

Loosely install four M6 x 45 mm (1.8 inch) screws.






4. NOTE: The main control valve body screws will be tightened in later steps.

Loosely install two M6 x 35 mm (1.4 inch) screws.

5. Remove the special tools.






6. NOTE: The main control valve body screws will be tightened in later steps.

Loosely install the M6 x 30 mm (1.2 inch) screw.






7. NOTE: The main control valve body screws will be tightened in later steps.

Loosely install the sixteen M6 x 40 mm (1.6 inch) main control valve body screws.






8. Tighten the main control valve body screws in the sequence shown.

9. Rotate the manual lever into the NEUTRAL position.






10. Install the manual control valve detent lever spring.






11. Install the low/reverse band servo piston and rod.






12. Install the low/reverse band servo cover.

1. Install the low/reverse band servo cover and gasket.
2. Loosely install the low/reverse servo piston cover screws.






13. Tighten the servo cover screws in the sequence shown.






14. Connect the six solenoid electrical connectors.

1. Connect SSA, SSB, SSC, and SSD electrical connectors.
2. Connect the Torque Converter Clutch (TCC) solenoid electrical connector.
3. Connect the Electronic Pressure Control (EPC) solenoid electrical connector.






15. CAUTION: Excessive pressure may break the locating pins.

Install the main control valve body wire harness.

- Align the retaining pins to the holes in the solenoid clamps and press in the main control valve body wire harness guide and protector.






16. Install the transmission fluid filter.

1. Install the transmission fluid filter.
2. Install the transmission fluid filter screw.






17. Install the transmission fluid pan.

1. Position a new transmission fluid pan gasket on the transmission fluid pan.
2. Install and align the transmission fluid pan.






18. Tighten the transmission fluid pan screws.
- Tighten the transmission fluid pan screws in a crisscross sequence.






19. If equipped, position the servo heat shield over the servos and clip it to the pan rail.

20. NOTE: Start with a minimum of 3.7 liters (4 quarts) of clean automatic transmission fluid. Fill transmission with clean automatic transmission fluid to the correct fluid level.