Selector Lever Cable and Bracket - Floor Shift

Selector Lever Cable and Bracket - Floor Shift





Removal

All vehicles
1. With the vehicle in NEUTRAL, position it on a hoist.

Vehicles equipped with a 6R75 transmission
2. Remove the PRNDL trim, console tray and cup holder insert.





3. Remove the screw and the console upper trim.





4. NOTE: Selector lever bezel removed for clarity.

Disconnect the selector lever cable from the selector lever.
1 Disconnect the selector lever cable from the selector lever arm ball stud.
2 Disconnect the selector lever cable from the selector lever housing.





Vehicles equipped with a 6HP26 transmission
5. Remove the selector lever trim plate.





6. NOTE: Using a suitable tool, lift and remove the floor console upper panel from the rear.

Remove the floor console upper panel.





7. NOTE: Selector lever bezel removed for clarity.

Disconnect the selector lever cable from the selector lever arm ball stud.





8. Remove the center console LH kick panel.





9. Disconnect the selector lever cable from the selector lever housing.





All vehicles
10. Remove the selector lever cable and grommet.





11. If equipped, remove the heat shield.





12. Move the locking tab up and disconnect the selector lever cable from the manual control lever ball stud.





13. Remove the selector lever cable clip to release the selector lever cable from the bracket.





14. Remove the bolts and the selector lever cable bracket from the transmission.





Installation

All vehicles
1. Install the selector lever cable bracket and bolts onto the transmission.
^ Tighten to 25 Nm (18 lb-ft).





2. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.

Install the selector lever cable into the bracket and install the clip.





3. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.

Connect the selector lever cable onto the manual control lever ball stud and move the locking tab down.
^ Listen for the audible click.
^ Pull back on the selector lever cable to make sure that it is correctly installed.





4. If equipped, install the heat shield.





5. Install the selector lever cable and grommet.





Vehicles equipped with a 6R75 transmission

6. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.

NOTE: Selector lever bezel removed for clarity.

Connect the selector lever cable onto the selector lever.
1 Connect the selector lever cable onto the selector lever housing.
2 Connect the selector lever cable onto the selector lever arm ball stud.
^ Listen for the audible click.
^ Pull back on the selector lever cable to make sure that it is correctly installed.





7. Install the console upper trim and the screw.





8. Install the PRNDL trim, console tray and cup holder insert.





Vehicles equipped with a 6HP26 transmission

9. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.

Connect the selector lever cable onto the selector lever housing.





10. Install the center console LH kick panel.





11. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.

NOTE: Selector lever bezel removed for clarity.

Connect the selector lever cable onto the selector lever arm ball stud.
^ Listen for the audible click.
^ Pull back on the selector lever cable to make sure that it is correctly installed.





12. Install the floor console upper panel.





13. Install the selector lever trim plate.





All vehicles
14. Adjust the selector lever cable.