Power
LUMBAR ASSEMBLY - POWERExploded View
Front Seat Backrest, Manual and Power Recline, Without Fold Flat (Part 1):
Front Seat Backrest, Manual and Power Recline, Without Fold Flat (Part 2):
Front Seat Backrest, Manual Recline With Fold Flat (Part 1):
Front Seat Backrest, Manual Recline With Fold Flat (Part 2):
Seat Cushion With Power Seat Track (Part 1):
Seat Cushion With Power Seat Track (Part 2):
Driver Seat Cushion With Manual Seat Track (Part 1):
Driver Seat Cushion With Manual Seat Track (Part 2):
Passenger Seat Cushion With Manual Seat Track:
Passenger Power Seat Track (Part 1):
Passenger Power Seat Track (Part 2):
Special Tool(s)
Special Tool(s):
Removal and Installation
WARNING: Always carry or place a live air bag module with the air bag and deployment door/trim cover/tear seam pointed away from the body. Do not set a live air bag module down with the deployment door/trim cover/tear seam face down. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
NOTE:
- The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
- The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
All seats
1. Remove the front seat.
2. NOTE: The seat backrest trim cover and foam pad have been removed to show the backrest trim panel retainers.
Remove the backrest trim panel in the following sequence.
1 Release the 2 pin-type retainers at the bottom of the backrest trim panel.
2 Slide the backrest trim panel down to release the upper clips.
3 Turn the backrest trim panel to release the middle clips and remove the backrest trim panel.
3. NOTE: Lower outer J-clips are unfastened to show inner J-clips.
Release the backrest trim cover outer and inner J-clips attached to the backrest frame.
4. Remove the head restraint.
1 Using an appropriate tool, push in the hole, lift up on the head restraint and release one side of the head restraint.
2 Push the release button and remove the head restraint.
5. NOTE: Always install a new slave head restraint guide.
Pull out and remove the master and slave head restraint guides.
6. CAUTION: When installing, make sure the side air bag module wiring harness is not pinched between the side air bag module and the backrest frame or damage to the wiring harness can occur.
NOTE: When installing the side air bag module, new bolts must be installed.
Through the rear of the seat, remove and discard the 2 side air bag module bolts. Then separate the side air bag module from the seat backrest.
- To install, tighten to 23 Nm (17 lb-ft).
7. CAUTION:
- Do not pull the side air bag module electrical connector out by the locking button. Damage to the locking button can occur.
- Do not install the side air bag module electrical connector by the locking button. Damage to the locking button can occur.
- The side air bag module electrical connector locking button must be in the released position when the connector is being installed or connector damage may occur.
- The side air bag module electrical connector is unique and cannot be reversed when connected to the side air bag module. Match the electrical connector key to the keyway in the side air bag module. Do not force the electrical connector into the side air bag module or damage can occur.
Using a small screwdriver as shown, lift up and release the locking button on the side air bag module electrical connector. With the locking button released, remove the electrical connector and the side air bag module.
8. Separate the backrest frame from the backrest foam pad.
Seats with climate control
9. Remove the screw, release the 3 clips, disconnect the electrical connector and remove the backrest thermo-electric device (TED).
All seats
10. Remove the power lumbar assembly in the following sequence.
1 Disconnect the power lumbar motor.
2 Release the power lumbar assembly clip at the top of the backrest frame.
3 Slide the lumbar wire frame up and out at the bottom of the backrest frame.
4 Remove the power lumbar assembly.
11. To install, reverse the removal procedure.
12. Install the front seat. If a passenger seat has been serviced, do not prove out the SRS at this time.
Passenger seat
13. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test.