Selector Lever - Floor Shift
Selector Lever - Floor ShiftVehicles Equipped With a 6R75 Transmission
Vehicles Equipped With a 6HP26 Transmission
Removal
Vehicles equipped with a 6R75 transmission
1. Remove the PRNDL trim, console tray and cup holder insert.
2. Remove the screw and the console upper trim.
3. NOTE: Selector lever bezel removed for clarity.
Disconnect the selector lever cable from the selector lever.
1. Disconnect the selector lever cable from the selector lever arm ball stud.
2. Disconnect the selector lever cable from the selector lever housing.
4. Disconnect the selector lever electrical connector.
5. NOTE: Selector lever bezel removed for clarity.
Remove the bolts and lift the selector lever out of the console.
Vehicles equipped with a 6HP26 transmission
6. Remove the selector lever trim plate.
7. NOTE: Using a suitable tool, lift and remove the floor console upper panel from the rear.
Remove the floor console upper panel.
8. NOTE: Selector lever bezel removed for clarity.
Disconnect the selector lever cable from the selector lever arm ball stud.
9. Remove the center console LH kick panel.
10. Disconnect the selector lever cable from the selector lever housing.
11. Disconnect the selector lever electrical connector.
12. NOTE: Selector lever bezel removed for clarity.
Remove the bolts and lift the selector lever out of the console.
Installation
Vehicles equipped with a 6R75 transmission
1. NOTE: Selector lever bezel removed for clarity.
Install the sector lever into the console.
^ Tighten to 8 Nm (71 lb-inch).
2. Connect the selector lever electrical connector.
3. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.
NOTE: Selector lever bezel removed for clarity.
Connect the selector lever cable onto the selector lever.
1. Connect the selector lever cable onto the selector lever housing.
2. Connect the selector lever cable onto the selector lever arm ball stud.
^ Listen for the audible click.
^ Pull back on the selector lever cable to make sure that it is correctly installed.
4. Install the console upper trim and the screw.
5. Install the PRNDL trim, console tray and cup holder insert.
Vehicles equipped with a 6HP26 transmission
6. NOTE: Selector lever bezel removed for clarity.
Install the selector lever into the console.
^ Tighten to 8 Nm (71 lb-inch).
7. Connect the selector lever electrical connector.
8. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.
Connect the selector lever cable onto the selector lever housing.
9. Install the center console LH kick panel.
10. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place and the cable end is snapped onto the ball stud. Press the selector lever cable into the bracket and listen for the cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket. Also, make sure that the selector lever cable end is correctly installed onto the ball stud. Pull back on the selector lever cable to make sure that the cable end is correctly installed.
NOTE: Selector lever bezel removed for clarity.
Connect the selector lever cable onto the selector lever arm ball stud.
^ Listen for the audible click.
^ Pull back on the selector lever cable to make sure that it is correctly installed.
11. Install the floor console upper panel.
12. Install the selector lever trim plate.
All vehicles
13. Adjust the selector lever cable.