Pinpoint Test H: The Keyless Entry Keypad Illumination Is Inoperative/Does Not Operate Correctly
Handles, Locks, Latches and Entry Systems
Pinpoint Tests
Pinpoint Test H: The Keyless Entry Keypad Illumination Is Inoperative/Does Not Operate Correctly
Refer to Wiring Diagram Set 117, Remote Keyless Entry and Alarm for schematic and connector information. Diagrams By Number
Normal Operation
When any keypad button is touched the Smart Junction Box (SJB) sends voltage to the keyless entry keypad LEDs on the illumination circuit to assist the driver in entering an access code at night. The keypad illumination has a dedicated ground circuit.
- DTC B1624 (Lamp Keypad Output Open Circuit) - an on-demand DTC that sets when the SJB detects an open or short to voltage on the keyless entry keypad illumination output circuit.
- DTC B1626 (Lamp Keypad Output Short Circuit to Ground) - a continuous DTC that sets when the SJB detects a short to ground on the keyless entry keypad illumination output circuit.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Keyless entry keypad
- SJB
PINPOINT TEST H: THE KEYLESS ENTRY KEYPAD ILLUMINATION IS INOPERATIVE/DOES NOT OPERATE CORRECTLY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery.
-------------------------------------------------
H1 CHECK THE KEYLESS ENTRY KEYPAD OPERATION
- Press the 7/8 and 9/0 buttons simultaneously on the keypad.
- Do the doors lock using the keyless entry keypad?
Yes
GO to H2.
No
GO to Pinpoint Test G. Pinpoint Test G: The Doors Do Not Lock/Unlock Using The Keyless Entry Keypad
-------------------------------------------------
H2 CHECK THE RECORDED SJB DTCs FROM THE SELF-TEST
- Check the recorded results from the SJB self-test.
- Is DTC B1624 or DTC B1626 present?
Yes
For DTC B1624, GO to H3.
For DTC B1626, GO to H9.
No
GO to H11.
-------------------------------------------------
H3 CHECK THE KEYLESS ENTRY KEYPAD ILLUMINATION
- Ignition OFF.
- Check the keyless entry keypad illumination.
- Is the keyless entry keypad illumination always on?
Yes
GO to H8.
No
GO to H4.
-------------------------------------------------
H4 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR REFERENCE VOLTAGE
NOTE: The SJB sends out a constant reference voltage on circuit CPK28 (WH/GN) for its own circuit diagnostics. This voltage is 10 volts +/- 1 volt.
- Disconnect: Keyless Entry Keypad C500 .
- Measure the voltage between the keyless entry keypad C500-6, circuit CPK28 (WH/GN), harness side and ground.
- Is 10 volts (+/- 1 volt) present?
Yes
GO to H5.
No
GO to H7.
-------------------------------------------------
H5 CHECK FOR SJB OUTPUT
- Enter the following diagnostic mode on the scan tool: SJB DataLogger .
- Measure the voltage between the keyless entry keypad C500-6, circuit CPK28 (WH/GN), harness side and ground while active commanding the SJB PID (KY_PAD_LMP) ON.
- Is the voltage greater than 11 volts?
Yes
GO to H6.
No
GO to H11.
-------------------------------------------------
H6 CHECK THE KEYPAD ILLUMINATION GROUND CIRCUIT FOR AN OPEN
- Disconnect: Negative Battery Cable .
- Measure the resistance between the keyless entry keypad C500-3, circuit GD133 (BK), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
INSTALL a new keyless entry keypad. REFER to Keyless Entry Keypad Service and Repair. CLEAR the DTCs. REPEAT the self-test.
No
REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------
H7 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR AN OPEN
- Disconnect: SJB C2280c .
- Measure the resistance between the keyless entry keypad C500-6, circuit CPK28 (WH/GN), harness side and the SJB C2280c-11, circuit CPK28 (WH/GN), harness side.
- Is the resistance less than 5 ohms?
Yes
GO to H11.
No
REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------
H8 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE
- Disconnect: SJB C2280c .
- Ignition ON.
- Observe the keypad illumination.
- Is the keypad still illuminated?
Yes
REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
No
GO to H11.
-------------------------------------------------
H9 CHECK THE KEYLESS ENTRY KEYPAD FOR A SHORT TO GROUND
- Disconnect: Keyless Entry Keypad C500 .
- NOTE: DTC B1624 may set and should be ignored when carrying out this step.
- Clear the DTCs, then repeat the SJB on-demand self-test.
- Is DTC B1626 recorded?
Yes
GO to H10.
No
INSTALL a new keyless entry keypad. REFER to Keyless Entry Keypad Service and Repair. TEST the system for normal operation.
-------------------------------------------------
H10 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR A SHORT TO GROUND
- Ignition OFF.
- Disconnect: SJB C2280c .
- Measure the resistance between the keyless entry keypad C500-6, circuit CPK28 (WH/GN), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
GO to H11.
No
REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------
H11 CHECK FOR CORRECT SJB OPERATION
- Disconnect all the SJB connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the SJB connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new SJB. REFER to Body Control Systems. TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------