Operation CHARM: Car repair manuals for everyone.

Part 2




Climate Control System

Dual Automatic Temperature Control (DATC) System

System Operation

The Dual Automatic Temperature Control (DATC) system maintains the selected vehicle interior temperature by heating and/or cooling the air.

- During A/C operation, the system reduces the relative humidity of the air inside the vehicle.

- The driver may override the automatic mode of operation.

- The temperature control setting is the desired cabin air temperature.

- The blower motor control override buttons vary the blower motor speed.

- The driver side and passenger side temperature settings can be individually controlled.

When the DATC (Dual Automatic Temperature Control) system is set to AUTO the air distribution direction, blower motor speed and A/C compressor operation and air inlet door mode are automatically controlled based on the temperature(s) selected.

The DATC (Dual Automatic Temperature Control) system manual override settings:

- allow the air distribution direction to be manually selected.

- allow the blower motor speed to be manually selected.

- allow recirculation mode to be manually selected in all modes except DEFROST. The A/C request can be manually selected by pressing the A/C request switch.

- allow A/C compressor operation to be manually selected except in DEFROST and FLOOR/DEFROST.

MyTemp

The MyTemp feature can be used to store and recall a preset driver's temperature. This feature is provided so this temperature can be quickly adjusted to a frequently used setting with a single button press.

Remote Start System Behavior - Message Center Set to Auto

This vehicle is equipped with a remote start feature. In addition to being able to start the vehicle remotely, the remote start feature also utilizes other vehicle systems to increase the level of comfort to the vehicle occupants upon entering the vehicle. For additional information on the remote start feature and the other vehicle systems it utilizes, refer to Starting System.

When the remote start feature is used, the climate control system automatically sets certain parameters in an attempt to achieve a comfortable cabin temperature. These parameters are set based on outside air temperature. During remote start, the outside air temperature is continually evaluated and HVAC system behavior can change if the outside air changes between cold, moderate and warm temperatures.

For additional information regarding the message center, refer to Instrument Panel, Gauges and Warning Indicators.

When Heater - A/C is set to Auto in the message center, the remote start sets the climate control system to the following settings:

For cold ambient air temperatures as determined by the HVAC module AUTO mode to request heat:

- the airflow mode is set to AUTO if Front Defrost is set to Off in the message center. (if the HVAC module requests FLOOR in AUTO mode, FLOOR/DEFROST will be used in remote start mode).

- the airflow mode is set to DEFROST if Front Defrost is set to Auto in the message center.

- the temperature is set to 22°C (72°F).

- the blower speed is set to AUTO.

- the air inlet mode is set to AUTO.

- A/C is set to AUTO.

For moderate and warm ambient air temperatures as determined by the HVAC module AUTO mode to request heat or cooling:

- the airflow mode is set to AUTO.

- the temperature is set to 22°C (72°F).

- the blower speed is set to AUTO.

- the air inlet mode is set to AUTO.

- A/C is set to AUTO.

Remote Start System Behavior - Message Center Set to Last User Settings

This vehicle is equipped with a remote start feature. In addition to being able to start the vehicle remotely, the remote start feature also utilizes other vehicle systems to increase the level of comfort to the vehicle occupants upon entering the vehicle. For additional information on the remote start feature and the other vehicle systems it utilizes, refer to Starting System.

When the remote start feature is used, the climate control system automatically sets certain parameters in an attempt to achieve a comfortable cabin temperature. These parameters are set based on outside air temperature. During remote start, the outside air temperature is continually evaluated and HVAC system behavior can change if the outside air changes between cold, moderate and warm temperatures.

For additional information regarding the message center, refer to Instrument Panel, Gauges and Warning Indicators.

When Heater - A/C is set to Last User Settings in the message center, the remote start sets the climate control system to the following settings:

For cold ambient air temperatures as determined by the HVAC module:

- the airflow mode is set to the last user setting if Front Defrost is set to Off in the message center.

- the airflow mode is set to DEFROST if Front Defrost is set to Auto in the message center.

- the temperature is set to the last user setting.

- the blower speed is set to the last user setting.

- the air inlet mode is set to the last user setting.

- A/C is set to the last user setting.

For moderate and warm ambient air temperatures as determined by the HVAC module AUTO mode to request heating or cooling:

- the airflow mode is set to the last user setting.

- the temperature is set to the last user setting.

- the blower speed is set to the last user setting.

- the air inlet mode is set to the last user setting.

- A/C is set to the last user setting.

System Airflow and Mode Description

AUTO

When AUTO is selected:

- the temperature control setting is manually set to the desired setting.

- the air inlet door is automatically controlled by the HVAC module based on the temperature setting.

- the mode door is automatically controlled by the HVAC module based on the temperature setting.

- the temperature blend doors are automatically controlled by the HVAC module, based on the temperature setting.

- the A/C compressor is automatically controlled by the HVAC module, based on the temperature setting. The A/C compressor will not operate if the outside temperature is below approximately 6°C (43°F).

- the blower motor is on. The blower motor speed is automatically controlled by the HVAC module based on the temperature setting, but can be manually overridden.

OFF

When OFF is selected:

- the air inlet door closes, preventing outside air and allowing only recirculated air.

- the blower motor is off.

Max A/C

When MAX A/C is selected:

- the air inlet door closes, preventing outside air and allows only recirculated air.

- the RECIRC button is disabled and the indicator is illuminated (RECIRC forced on).

- the mode doors direct airflow to the instrument panel A/C registers.

- blended air temperature is available.

- the A/C request button is illuminated and will be disabled.

- the A/C compressor operates if the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.

PANEL

When PANEL is selected:

- the RECIRC request button is enabled. If the RECIRC request button is selected (indicator on), the air inlet door closes, preventing outside air from entering the passenger compartment. If the RECIRC request button is not selected (indicator off), the air inlet door opens, allowing only outside air into the passenger compartment.

- the mode doors direct airflow to the instrument panel A/C registers.

- blended air temperature is available. Only when A/C compressor operation has been selected by pressing the A/C request button (indicator on) can the airflow temperature be cooled below the outside air temperature.

- the A/C request button is enabled. The A/C compressor operates and the indicator illuminates if the A/C request button is selected and the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.

PANEL/FLOOR

When PANEL/FLOOR is selected:

- the RECIRC request button is enabled. If the RECIRC request button is selected (indicator on), the air inlet door closes, preventing outside air from entering the passenger compartment. If the RECIRC request button is not selected (indicator off), the air inlet door opens, allowing only outside air into the passenger compartment.

- the mode doors direct airflow to the floor duct and the instrument panel A/C registers. A small amount of airflow from the side window demisters and defrost duct is present.

- blended air temperature is available. Only when A/C compressor operation has been selected by pressing the A/C request button (indicator on) can the airflow temperature be cooled below the outside air temperature.

- the A/C request button is enabled. The A/C compressor operates and the indicator illuminates if the A/C request button is selected and the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.

FLOOR

When FLOOR is selected:

- the RECIRC request button is enabled. If the RECIRC request button is selected (indicator on), the air inlet door closes, preventing outside air from entering the passenger compartment. If the RECIRC request button is not selected (indicator off), the air inlet door opens, allowing only outside air into the passenger compartment.

- the mode doors direct airflow to the floor duct. A small amount of airflow from the defroster duct and side window demisters is present.

- blended air temperature is available. Only when A/C compressor operation has been selected by pressing the A/C request button (indicator on) can the airflow temperature be cooled below the outside air temperature.

- the A/C request button is enabled. The A/C compressor operates and the indicator illuminates if the A/C request button is selected and the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.

FLOOR/DEFROST

When FLOOR/DEFROST is selected:

- the RECIRC request button is enabled. If the RECIRC request button is selected (indicator on), the air inlet door closes, preventing outside air from entering the passenger compartment. If the RECIRC request button is not selected (indicator off), the air inlet door opens, allowing only outside air into the passenger compartment.

- the mode doors direct airflow to the floor duct, the defroster duct and the side window demisters.

- blended air temperature is available.

- the A/C request button is enabled. The A/C compressor operates automatically and the indicator illuminates if the A/C request button is selected and the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.

DEFROST

When DEFROST is selected:

- the RECIRC request button and indicator is disabled. Regardless of button and indicator status, the air inlet door opens, allowing only outside air into the passenger compartment.

- the mode doors direct airflow to the defroster duct and side window demisters. A small amount of airflow from the floor duct is present.

- blended air temperature is available.

- the A/C request button is enabled. The A/C compressor operates automatically and the indicator illuminates if the A/C request button is selected and the outside temperature is above approximately 6°C (43°F).

- the blower motor is on.